Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2019 Genesis G70 2.0T Advanced, AWDFACTORY OEM SERVICE PROCEDURE
Electronic Stability Control DTCS
ELECTRONIC STABILITY CONTROL DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION
| DTC | Description |
|---|---|
| DTC C1100 | 01: Battery Voltage |
| DTC C1101 | 01: Battery-Voltage High |
| DTC C1102 | 01: Battery-Voltage Low |
| DTC C1103 | 01: Ignition Voltage |
| DTC C1114 | 01: 12V Sensor Power Fail |
| DTC C1200 | 01: Wheel Speed Sensor Front-LH Open/Short |
| DTC C1201 | 02: Wheel Speed Sensor Front-LH Range/Performance/Intermittent |
| DTC C1202 | 02: Wheel Speed Sensor Front-LH Invalid/no Signal |
| DTC C1203 | 01: Wheel Speed Sensor Front-RH Open/Short |
| DTC C1204 | 02: Wheel Speed Sensor Front-RH Range/Performance/Intermittent |
| DTC C1205 | 02: Wheel Speed Sensor Front-RH Invalid/no Signal |
| DTC C1206 | 01: Wheel Speed Sensor Rear-LH Open/Short |
| DTC C1207 | 02: Wheel Speed Sensor Rear-LH Range/Performance/Intermittent |
| DTC C1208 | 02: Wheel Speed Sensor Rear-LH Invalid/no Signal |
| DTC C1209 | 01: Wheel Speed Sensor Rear-RH Open/Short |
| DTC C1210 | 02: Wheel Speed Sensor Rear-RH Range/Performance/Intermittent |
| DTC C1211 | 02: Wheel Speed Sensor (Rear Right)-Invalid/No Signal |
| DTC C1235 | 01: Pressure Sensor (Primary) - Electrical |
| DTC C1237 | 02: Pressure Sensor - Other |
| DTC C1260 | 02: Steering Angle Sensor Circuit - Signal |
| DTC C1261 | 04: Steering Angle Sensor is Not Calibrated |
| DTC C1282 | 08: Yaw Rate & G Sensor-Electrical |
| DTC C1283 | 02: Lateral G/Longitudinal G/Yaw Rate Sensor-Signal Error |
| DTC C1285 | 04: Uncalibrated Ax Signal |
| DTC C1286 | 01: Yaw Rate & G Sensor Fail-Replace SRSCM |
| DTC C1358 | 01: AVH not Available due to EPB in Emergency Release |
| DTC C1382 | 01: Lever Hall Sensor Fault |
| DTC C1383 | 01: Actuator Hall Sensor Fault |
| DTC C1385 | 01: Vacuum Sensor-Electrical |
| DTC C1386 | 02: Vacuum Sensor-Signal |
| DTC C1501 | 01: Switch-Failure |
| DTC C1503 | 01: TCS Switch Error |
| DTC C1520 | 01: Clutch Switch |
| DTC C1527 | 01: Reverse Gear Signal Error |
| DTC C1539 | 01: In Gear Switch Error |
| DTC C1542 | 01: Brake Circuit Error |
| DTC C1604 | 04: ECU Hardware Error |
| DTC C160E | 08: P-CAN Bus Off |
| DTC C1611 | 08: CAN Timeout-EMS |
| DTC C1612 | 08: CAN Time-out TCU |
| DTC C1613 | 08: CAN Signal Error EMS |
| DTC C1616 | 08: C-CAN Bus OFF |
| DTC C1623 | 08: CAN Timeout-Steering Angle Sensor |
| DTC C1627 | 08: CAN Time-out 4WD |
| DTC C1628 | 08: CAN Timeout-Cluster |
| DTC C162A | 08: CAN Time-Out Cluster for Driving Mode |
| DTC C162B | 08: CAN Time-out ECS_IVSS11 |
| DTC C162C | 02: CAN Signal Failure ECS_IVSS11 |
| DTC C162E | 04: IVSS SW Execution Time Failure |
| DTC C1638 | 08: ACC SCC Communication Error |
| DTC C1643 | 08: CAN Time out Yaw Rate & G Sensor |
| DTC C1648 | 08: CAN Signal Error EMS for ACC SCC |
| DTC C1649 | 08: CAN Time Out ECM for ACC |
| DTC C1650 | 08: CAN Signal Error SCC |
| DTC C1656 | 08: CAN Signal Error Cluster |
| DTC C1687 | 08: CAN Time out VSM2 MDPS |
| DTC C1688 | 08: VSM2 (MDPS) Signal Error |
| DTC C16B8 | 08: AEB Communication Error |
| DTC C1702 | 04: Variant Coding Error |
| DTC C1710 | 04: Assembly line Setup is still Active |
| DTC C1713 | 04: Factory Mode Not Disabled |
| DTC C1812 | 08: CAN Timeout Gateway |
| DTC C1817 | 08: CAN Signal Error Gateway |
| DTC C2112 | 01: Valve Relay Error |
| DTC C2126 | 01: Vacuum Pump Relay Drive Pin Open Short |
| DTC C2220 | 01: Rear LH Actuator |
| DTC C2222 | 08: Actuator Failure 4WD |
| DTC C2224 | 01: Rear RH (or rear) Actuator |
| DTC C2227 | 07: Excessive Temperature Of Brake Disc |
| DTC C2228 | 08: Actuator Failure TCU |
| DTC C2229 | 08: Actuator Failure EMS |
| DTC C2231 | 02: Vacuum Pump System Fail |
| DTC C2243 | 08: Gear Fault |
| DTC C2380 | 01: ABS TCS ESP valve error |
| DTC C2402 | 01: Motor Electrical |
| DTC C2416 | 01: Motor Short or Open LH |
| DTC C2417 | 01: Motor Short or Open RH |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.