Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2017 Genesis G90 3.3T Premium, AWDFACTORY OEM SERVICE PROCEDURE
4WD Control DTCS
4WD CONTROL DIAGNOSTIC TROUBLE CODE IDENTIFICATION
| DTC | Description |
|---|---|
| DTC P173600 | Motor supply Voltage high |
| DTC P173700 | Motor supply Voltage Low voltage |
| DTC P175600 | EMS Internal Error |
| DTC P178000 | Control Unit Supply High Voltage |
| DTC P178100 | Control Unit Supply Low Voltage |
| DTC P310000 | Control Module - Failure Motorwinding |
| DTC P310100 | Control Module - Motor Overcurrent |
| DTC P310200 | Control Module - Control ASIC Overtemperature |
| DTC P310300 | Control Module - Failure Position Sensor |
| DTC P310400 | Control Module - Failure Current Measurement |
| DTC P310500 | Control Module - Failure external Watchdog disabled |
| DTC P310600 | Control Module - Failure external Watchdog Test |
| DTC P310700 | Motor Supply Voltage Open Circuit |
| DTC P310800 | Control Unit Supply Voltage Open Circuit |
| DTC P310900 | System Failure - Torque Tube Violation |
| DTC P310A00 | System Failure - Initial Position Search Failed |
| DTC P310B00 | System Failure - Initial Position drift |
| DTC P310C00 | System Failure - implausible Calibration value |
| DTC P310D00 | System Failure - Position failure During Calibration |
| DTC P310E00 | Mechanical Failure - Angele limit exceed |
| DTC P310F00 | System Failure - Maximal Clutch Stress |
| DTC P311000 | System Failure - Maximal ECU Stress |
| DTC P311100 | Mechanical Failure - Clutch Worn |
| DTC P311200 | Mechanical Failure - Oil Worn |
| DTC P311300 | Initial Calibration not done |
| DTC P311400 | Vehicle information option not detected or invalid |
| DTC P311500 | HW Classification Missing |
| DTC P311600 | Insufficient CAN Signals - Driving Stability |
| DTC P311700 | Insufficient CAN Signal - TC Protection |
| DTC P311800 | Insufficient CAN Signals - Driving Inconvenience Signals |
| DTC P311900 | Insufficient CAN Signals - Driving Inconvenience Tires |
| DTC U000100 | High Speed CAN Communication Bus |
| DTC U010000 | Lost Communication With ECM/PCM'A' |
| DTC U010100 | Lost Communication With TCM |
| DTC U012100 | Lost Communication With Anti-Lock Brake System (ABS) |
| DTC U012200 | Lost Communication With Vehicle Dynamics Control Module (C-CAN) |
| DTC U012600 | Lost Communication With Steering Angle Sensor Module |
| DTC U014600 | Lost Communication With Gateway or Cluster |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
