2021 GMC Yukon AT4FACTORY OEM SERVICE PROCEDURE

Engine Assembly: Remove, Install, and Overhaul

WARNING: This page is about the Yukon Denali, 3.0L Eng VIN T, 4WD, which is a different variant/trim than selected.
Includes: Replace Rings, Main and Rod Bearings, Camshaft(s), Crankshaft and Timing Components. Remove Cylinder ridge, burnish Cylinders, grind Valves and clean and test or replace Lifters. Includes (where applicable): Adjust Valves. DOES NOT include Pin fit or rebore and align Rods. See machine operations.

Applies ToNoteStandard HoursWarranty HoursSkill Level
3.0L Eng,4WD, w/Air SuspensionIncludes: R&I Wiper Link Assembly & Cowl Top Panel. Includes: R&I Fender Liners. Includes: R&I Front Bumper Cover and Headlamp Assemblies. DOES NOT include Headlamp adjustment. Includes: R&I Cooling Module. Includes: R&I Catalytic Converters. Includes: R&I Charge Air Cooler. Includes: R&I Alternator. Includes: R&I Starter Assembly. Includes: R&I Air Conditioning Compressor. Includes: R&I Air Cleaner. Includes: R&I Battery and Tray. Includes: Drain and refill Cooling System. Includes: Drain and refill Engine Oil. Includes: Perform Filter Life Monitor Reset procedure. DOES NOT include Air Conditioning System recover, evacuate and recharge.48.2A
3.0L Eng,4WD, w/o Air SuspensionIncludes: R&I Wiper Link Assembly & Cowl Top Panel. Includes: R&I Fender Liners. Includes: R&I Front Bumper Cover and Headlamp Assemblies. DOES NOT include Headlamp adjustment. Includes: R&I Cooling Module. Includes: R&I Catalytic Converters. Includes: R&I Charge Air Cooler. Includes: R&I Alternator. Includes: R&I Starter Assembly. Includes: R&I Air Conditioning Compressor. Includes: R&I Air Cleaner. Includes: R&I Battery and Tray. Includes: Drain and refill Cooling System. Includes: Drain and refill Engine Oil. Includes: Perform Filter Life Monitor Reset procedure. DOES NOT include Air Conditioning System recover, evacuate and recharge.48.0A
Additional Procedure: ENGINE ASSEMBLY: Remove, Install, and Overhaul:
Where Skid Plate interferes add0.2A
Combination Procedure: CRANKSHAFT POSITION SENSOR: Reset:
Crankshaft Position Variation LearnIncludes: Additional time for use of scan tool to perform this procedure.0.2B
Combination Procedure: FUEL INJECTION SYSTEM: Reset:
3.0L Eng, Fuel System Reset ProcedureIncludes: Additional time for use of scan tool to perform this procedure.0.2B
Combination Procedure: FUEL INJECTOR: Program:
3.0L Eng, Fuel Injector Flow Rate ProgrammingIncludes: Additional time for use of scan tool to perform this procedure.0.2B
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.