Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSGMC2020ACADIA SLREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 34 (PROGRAMMING AND SETUP)
2020 GMC Acadia SL
Section 34 (Programming And Setup)
2020 GMC Acadia SLSECTION Section 34 (Programming And Setup)
WARNING: This page is about a different car, the 2019 GMC Acadia. However, it is still accessible from the selected car via links, so may be relevant.
- Diagnostic Information and Procedures
- Repair Instructions
- A11 Radio: Programming and Setup (IO5/IO6)
- A11 Radio: Programming and Setup (IOB)
- A11 Radio: Programming and Setup (IOU)
- A22 Radio Controls: Programming and Setup
- A26 HVAC Controls: Programming and Setup
- B174W Frontview Camera - Windshield: Programming and Setup
- B218L Side Object Sensor Module - Left: Programming and Setup
- B218R Side Object Sensor Module - Right: Programming and Setup
- B233B Radar Sensor Module - Long Range: Programming and Setup
- K9 Body Control Module: Programming and Setup
- K17 Electronic Brake Control Module: Programming and Setup
- K19 Suspension Control Module: Programming and Setup
- K20 Engine Control Module: Programming and Setup
- K29F Seat Heating Control Module - Front: Programming and Setup
- K29R Seat Heating Control Module - Rear: Programming and Setup
- K32 Steering Wheel Heating Control Module: Programming and Setup
- K33 HVAC Control Module: Programming and Setup
- K36 Inflatable Restraint Sensing and Diagnostic Module: Programming and Setup
- K36 Inflatable Restraint Sensing and Diagnostic Module: Configure New Module
- K39 Liftgate Control Module: Programming and Setup
- K40D Seat Memory Control Module - Driver: Programming and Setup
- K43 Power Steering Control Module: Programming and Setup
- K47 Rear Differential Clutch Control Module: Programming and Setup
- K56 Serial Data Gateway Module: Programming and Setup (GMC)
- K56 Serial Data Gateway Module: Programming and Setup (Holden)
- K60 Steering Column Lock Module: Programming and Setup
- K61 Sunroof Control Module: Programming and Setup
- K71 Transmission Control Module: Programming and Setup (9T45 (M3U) or 9T50 (M3D, M3H))
- K73 Telematics Communication Interface Control Module: Programming and Setup
- K74 Human Machine Interface Control Module: Programming and Setup
- K84 Keyless Entry Control Module: Programming and Setup
- K85 Passenger Presence Module: Programming and Setup
- K89 Immobilizer Control Module: Programming and Setup
- K99 Steering Column Position Control Module: Programming and Setup
- K124 Active Safety Control Module: Programming and Setup
- K157 Video Processing Control Module: Programming and Setup
- K171 Hands-Free Liftgate Sensor Control Module: Programming and Setup
- K182 Parking Assist Control Module: Programming and Setup
- K188 Human Machine Interface Control Module Bypass Module Programming and Setup
- P16 Instrument Cluster: Programming and Setup
- K71 Transmission Control Module or Q8 Control Solenoid Valve Assembly: Programming and Setup (6T50 (M2D))
- K71 Transmission Control Module or Q8 Control Solenoid Valve Assembly: Programming and Setup (6T70 (M7U M7W))
- T3 Audio Amplifier: Programming and Setup
- Fuel Pump Power Control Module Programming and Setup
- Service Programming System (SPS)
- Special Tools and Equipment
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.