Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2018 GMC Terrain SLFACTORY OEM SERVICE PROCEDURE
Circuit/System Testing
- Ignition - On / Vehicle - In Service Mode
- Disconnect the electrical connector: X1 K9 Body Control Module
- Verify a test lamp turns On between the test points: B+ circuit terminal 4 & Ground
- If the test lamp does not turn On
- Ignition/Vehicle - Off & Remove - Test lamp
- Disconnect the electrical connector: T19 Power Supply Transformer
- Test for less than 2 Ω between the test points: B+ circuit terminal 4 & Circuit terminal 9 @ T19 Power Supply Transformer
- If 2 Ω or greater - Repair the open/high resistance in the circuit.
- If less than 2 Ω - Replace the component:T19 Power Supply Transformer
- Go to next step: If the test lamp turns On
- Ignition/Vehicle & All vehicle systems - Off
- Disconnect the electrical connector:S3 Transmission Shift Lever
- Test for less than 10 Ω between the test points:Ground circuit terminal 2 & Ground
- If 10 Ω or greater
- Disconnect ground terminal.
- Test for less than 2 Ω between the test points:Ground circuit terminal 2 & Ground
- If 2 Ω or greater - Repair the open/high resistance in the circuit.
- If less than 2 Ω - Repair the open/high resistance in the ground connection.
- Go to next step: If less than 10 Ω
- Connect a test lamp between the test points:Control circuit terminal 4 & Ground circuit terminal 2
- Ignition - On / Vehicle - In Service Mode
- Perform the scan tool control function:Brake Transmission Shift Interlock Solenoid Actuator
Verify the test lamp turns On and Off.
- If the test lamp is always Off
- Ignition/Vehicle - Off & Remove - Test lamp
- Disconnect the electrical connector:K9 Body Control Module
- Test for infinite resistance between the test points:Control circuit terminal 4 @ Component harness & Ground
- If less than infinite resistance - Repair the short to ground on the circuit.
- If infinite resistance
- Test for less than 2 Ω between the test points: Control circuit terminal 4 @ Component harness & Terminal 6 X7 @ Control module harness
- If 2 Ω or greater - Repair the open/high resistance in the circuit.
- If less than 2 Ω Replace the component:K9 Body Control Module
- If the test lamp is always On
- Ignition/Vehicle - Off & Remove - Test lamp
- Disconnect the electrical connector:K9 Body Control Module
- Ignition - On / Vehicle - In Service Mode
- Test for less than 1 V between the test points:Control circuit terminal 4 @ Component harness & Ground
- If 1 V or greater - Repair the short to voltage on the circuit.
- If less than 1 V - Replace the component:K9 Body Control Module
- Go to next step: If the test lamp turns On and Off
- Test or replace the component:S3 Transmission Shift Lever
NOTE:
It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
