Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Circuit/System Testing
Perform the Circuit/System Verification before proceeding with Circuit/System Testing.
Frontview Camera Module Malfunction without Active Safety System, UGN
- Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the K109 Frontview Camera Module. It may take up to 2 min for all vehicle systems to power down.
- Test for less than 10 Ω between the ground circuit terminal 1 and ground.
- If 10 Ω or greaterÂ
- Ignition OFF.
- Test for less than 2 Ω in the ground circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, repair the open/high resistance in the ground connection.
- If less than 10 ΩÂ
- Verify a test lamp illuminates between the B+ circuit terminal 3 and ground.
- If the test lamp does not illuminate and the circuit fuse is goodÂ
- Ignition OFF.
- Test for less than 2 Ω in the B+ circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
- If the test lamp does not illuminate and the circuit fuse is openÂ
- Ignition OFF.
- Test for infinite resistance between the B+ circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance, replace the K109 Frontview Camera Module.
- If the test lamp illuminatesÂ
- Replace the K109 Frontview Camera Module.
Frontview Camera Module Malfunction with Active Safety System, UGN
- Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the K109 Frontview Camera Module. It may take up to 2 min for all vehicle systems to power down.
- Test for less than 10 Ω between the ground circuit terminal 5 and ground.
- If 10 Ω or greaterÂ
- Ignition OFF.
- Test for less than 2 Ω in the ground circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, repair the open/high resistance in the ground connection.
- If less than 10 ΩÂ
- Verify a test lamp illuminates between the B+ circuit terminal 2 and ground.
- If the test lamp does not illuminate and the circuit fuse is goodÂ
- Ignition OFF.
- Test for less than 2 Ω in the B+ circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
- If the test lamp does not illuminate and the circuit fuse is openÂ
- Ignition OFF.
- Test for infinite resistance between the B+ circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance, replace the K109 Frontview Camera Module.
- If the test lamp illuminatesÂ
- Replace the K109 Frontview Camera Module.
Forward Collision Alert Indicator Malfunction
- Ignition OFF, and all vehicle systems OFF, disconnect the harness connector at the P43 Collision Alert Indicators. It may take up to 2 min for all vehicle systems to power down.
- Test for less than 10 Ω between the ground circuit terminal 4 and ground.
- If 10 Ω or greaterÂ
- Ignition OFF.
- Test for less than 2 Ω in the ground circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, repair the open/high resistance in the ground connection.
- If less than 10 ΩÂ
- Ignition ON.
- Verify a test lamp illuminates between the ignition circuit terminal 1 and ground.
- If the test lamp does not illuminate and the circuit fuse is goodÂ
- Ignition OFF.
- Test for less than 2 Ω in the ignition circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, refer to Power Mode Mismatch (Without KL9)Power Mode Mismatch (With KL9) .
- If the test lamp does not illuminate and the circuit fuse is openÂ
- Ignition OFF.
- Test for infinite resistance between the ignition circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance, replace the P43 Collision Alert Indicators.
- If the test lamp illuminatesÂ
- Connect a test lamp between the control circuit terminal 2 and the ignition circuit terminal 1.
- Verify the test lamp turns ON and OFF when commanding the Instrument Cluster All Indicators On and Off with a scan tool.
- If the test lamp is always OFFÂ
- Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster, ignition ON.
- Test for less than 1 V between the control circuit and ground.
- If 1 V or greater, repair the short to voltage on the circuit.
- If less than 1 V
- Ignition OFF.
- Test for less than 2 Ω in the control circuit end to end.
- If 2 Ω or greater, repair the open/high resistance in the circuit.
- If less than 2 Ω, replace the P16 Instrument Cluster.
- If the test lamp is always ONÂ
- Ignition OFF, disconnect the harness connector at the P16 Instrument Cluster.
- Test for infinite resistance between the control circuit and ground.
- If less than infinite resistance, repair the short to ground on the circuit.
- If infinite resistance, replace the P16 Instrument Cluster.
- If the test lamp turns ON and OFFÂ
- Test or replace the P43 Collision Alert Indicators.
Forward Collision Alert Switch Malfunction
- Ignition OFF, disconnect the X3 harness connector at the K9 Body Control Module, ignition ON.
- Test for less than 1 V between the signal circuit terminals listed below and ground:
- Terminal 4
- Terminal 16
- If 1 V or greaterÂ
Repair the short to voltage on the signal circuit.
- If less than 1 VÂ
- Ignition OFF.
- Test for infinite resistance between the signal circuit terminals listed below and ground:
- Terminal 4
- Terminal 16
- If less than infinite resistanceÂ
Repair the short to ground on the signal circuit.
- If infinite resistanceÂ
- Test for 7.0k - 10.5k Ω between signal circuit terminals 4 and signal circuit terminal 16.
- If greater than 10.5k Ω Â
- Disconnect the harness connector at the S70L Steering Wheel Controls Switch - Left.
- Test for less than 5 Ω between the circuit terminals listed below:
- S70L Steering Wheel Controls Switch - Left terminal 8 and K9 Body Control Module terminal 4.
- S70L Steering Wheel Controls Switch - Left terminal 9 and K9 Body Control Module terminal 16.
- If greater than 5 Ω, repair the open/high resistance in the circuit.
- If less than 5 Ω, test or replace the S70L Steering Wheel Controls Switch - Left.
- If less than 7.0k ΩÂ
- Disconnect the harness connector at the S70L Steering Wheel Controls Switch - Left.
- Verify infinite resistance between signal circuit terminals 4 and signal circuit terminal 16
- If less than infinite resistance, repair short in circuit.
- If infinite resistance, test or replace the S70L Steering Wheel Controls Switch - Left.
- If between 7.0k - 10.5k ΩÂ
- Test for 2.1k - 3.2k Ω between signal circuit terminals 4 and signal circuit terminal 16 while pressing forward collision alert switch.
- If not between 2.1k - 3.2k ΩÂ
Test or replace the S70L Steering Wheel Controls Switch - Left.
- If between 2.1k - 3.2k ΩÂ
- If not between 2.1k - 3.2k ΩÂ
- Replace the K9 Body Control Module.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
