Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2010 GMC Terrain SLE, 3.0 Y, AWDFACTORY OEM SERVICE PROCEDURE
Wiring Systems And Power Management - Diagnostic Information And Procedures
- Diagnostic Information and Procedures
- Diagnostic Code Index
- DTC B1370-B1379, B1380-B1389, or B1440-B1443
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Actions Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC B1445
- DTC B144A
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC B144B
- Diagnostic Instructions
- DTC Descriptor
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Action Taken When the DTC Sets
- Conditions for Clearing the DTC
- Diagnostic Aids
- Reference Information
- Circuit/System Testing
- Component Testing
- Repair Procedures
- DTC B147E
- DTC B147F
- Symptoms - Wiring Systems
- Ignition Can/Cannot Be Turned Off with Transmission in Any Gear
- Power Mode Mismatch
- Diagnostic Instructions
- DTC Descriptors
- Diagnostic Fault Information
- Circuit/System Description
- Conditions for Running the DTC
- Conditions for Setting the DTC
- Actions Taken When the DTC Sets
- Conditions for Clearing the DTC
- Reference Information
- Circuit/System Verification
- Circuit/System Testing
- Component Testing
- Repair Procedures
- Retained Accessory Power Malfunction
- General Electrical Diagnosis
- Checking Aftermarket Accessories
- Circuit Testing
- Basic Digital Multimeter Requirements
- Using Connector Test Adapters
- Probing Electrical Connectors
- Troubleshooting with a Digital Multimeter
- Troubleshooting with a Test Lamp
- Using Fused Jumper Wires
- Measuring Voltage
- Measuring Voltage Drop
- Measuring Frequency
- Testing Ground and Low Reference Circuits
- Testing for Continuity
- Testing for Short to Ground
- Testing for a Short to Voltage
- Testing for Intermittent Conditions and Poor Connections
- Inducing Intermittent Fault Conditions
- Testing for Electrical Intermittents
- Scan Tool Snapshot Procedure
- Circuit Protection - Fuses
- Circuit Protection - Circuit Breakers
- Circuit Protection - Fusible Links
- Wiring Repairs
- Repairing Damaged Wire Insulation
- Flat Wire Repairs
- GMLAN Wiring Repairs
- High Temperature Wiring Repairs
- Heated Oxygen Sensor Wiring Repairs
- Splicing Copper Wire Using Splice Sleeves
- Splicing Twisted or Shielded Cable
- Splicing Inline Harness Diodes
- SIR/SRS Wiring Repairs
- Connector Repairs
- Connector Position Assurance Locks
- Terminal Position Assurance Locks
- AFL/EPC Connectors
- Bosch Connectors (BSK)
- Bosch Connectors (0.64)
- Bosch Connectors (2.8 JPT)
- Bosch Connectors (ECM)
- Delphi Connectors (Weather Pack)
- Delphi Connectors (Push To Seat)
- Delphi Connectors (Pull To Seat)
- Delphi Connectors (Micro-Pack 100W)
- Delphi Connectors (Micro .64)
- Delphi Connectors (12-Way)
- Delphi Connectors (Steering Gear)
- FCI Connectors (Lever Lock)
- FCI Connectors (SIR)
- FEP Connectors (Steering Gear)
- JST Connectors
- Kostal Connectors (Glow Plug Control Module)
- Kostal Connectors (Transmission)
- Molex Connectors
- Sumitomo Connectors
- Tyco/AMP Connectors (CM 42-Way)
- Tyco/AMP Connectors (Sensor)
- Tyco/AMP Connectors (0.25 Cap)
- Tyco/AMP Connectors (43-Way)
- Tyco/AMP Connectors (Door Module)
- Yazaki Connectors (2-Way)
- Yazaki Connectors (16-Way)
- Repairing Connector Terminals
- Terminal Wiring Repair
- Terminated Lead Repair
- Ignition Key Cannot Be Removed from the Ignition Lock Cylinder
- Ignition Key Cannot Turn or Sticks in Any Position
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.