Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 GMC Canyon 2WD L4-2.9LFACTORY OEM SERVICE PROCEDURE
Coolant Temperature Sensor/Switch (For Computer): Service and Repair
Service Precautions
Engine Coolant Temperature Sensor Replacement
Tools Required
J 45861 ECT Sensor Socket
Removal Procedure

1. Partially drain the cooling system to a level below the engine coolant temperature (ECT) sensor. Refer to Draining and Filling Cooling System (Static Fill) Draining and Filling Cooling System (Vac N Fill).
2. Disconnect the engine wiring harness electrical connector (1) from the ECT sensor electrical connector.
3. Remove the ECT sensor electrical connector from the camshaft cover.
Notice: Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.
4. Using the J 45861 (2), carefully remove the ECT sensor from the cylinder head.
Installation Procedure
Notice: Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.
Notice: Replacement components must be the correct part number for the application. Components requiring the use of the thread locking compound, lubricants, corrosion inhibitors, or sealants are identified in the service procedure. Some replacement components may come with these coatings already applied. Do not use these coatings on components unless specified. These coatings can affect the final torque, which may affect the operation of the component. Use the correct torque specification when installing components in order to avoid damage.

1. If installing the original sensor or a NEW sensor without sealant, apply thread sealer GM P/N 12346004 (Canadian P/N 10953480) or equivalent.
2. Thread the ECT sensor into the cylinder head by hand.
Notice: Refer to Component Fastener Tightening Notice in Service Precautions.
3. Using the J 45861 (2), tighten the ECT sensor.
Tighten the sensor to 14 N.m (10 lb ft).
4. Install the ECT sensor electrical connector to the camshaft cover.
5. Connect the engine wiring harness electrical connector (1) to the ECT sensor electrical connector.
6. Refill the cooling system. Refer to Draining and Filling Cooling System (Static Fill) Draining and Filling Cooling System (Vac N Fill).
Engine Coolant Temperature Sensor Replacement
Tools Required
J 45861 ECT Sensor Socket
Removal Procedure
1. Partially drain the cooling system to a level below the engine coolant temperature (ECT) sensor. Refer to Draining and Filling Cooling System (Static Fill) Draining and Filling Cooling System (Vac N Fill).
2. Disconnect the engine wiring harness electrical connector (1) from the ECT sensor electrical connector.
3. Remove the ECT sensor electrical connector from the camshaft cover.
Notice: Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.
4. Using the J 45861 (2), carefully remove the ECT sensor from the cylinder head.
Installation Procedure
Notice: Use care when handling the coolant sensor. Damage to the coolant sensor will affect the operation of the fuel control system.
Notice: Replacement components must be the correct part number for the application. Components requiring the use of the thread locking compound, lubricants, corrosion inhibitors, or sealants are identified in the service procedure. Some replacement components may come with these coatings already applied. Do not use these coatings on components unless specified. These coatings can affect the final torque, which may affect the operation of the component. Use the correct torque specification when installing components in order to avoid damage.
1. If installing the original sensor or a NEW sensor without sealant, apply thread sealer GM P/N 12346004 (Canadian P/N 10953480) or equivalent.
2. Thread the ECT sensor into the cylinder head by hand.
Notice: Refer to Component Fastener Tightening Notice in Service Precautions.
3. Using the J 45861 (2), tighten the ECT sensor.
Tighten the sensor to 14 N.m (10 lb ft).
4. Install the ECT sensor electrical connector to the camshaft cover.
5. Connect the engine wiring harness electrical connector (1) to the ECT sensor electrical connector.
6. Refill the cooling system. Refer to Draining and Filling Cooling System (Static Fill) Draining and Filling Cooling System (Vac N Fill).
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
