1996 GMC Forward Control 7.4 JFACTORY OEM SERVICE PROCEDURE

Electrical Component Locator: Connectors

CONNECTORS

Component Component Location
C100 (Commercial Van) (Black, 7 Pin) Near windshield wiper motor.
C100 (Motor Home) (Gray, 36 Pin) Near relay bracket.
C100A (Black, 20 Pin) Below battery junction box.
C100B (Black, 10 Pin) Below battery junction box.
C100C (Black, 6 Pin) Below battery junction box.
C101 (Black, 7 Pin) Above left rear of intake manifold.
C102 (Commercial Van) (Black, 3 Pin) Approximately, 15 cm from ignition control module.
C102 (Motor Home) At right front of engine.
C103 (Commercial Van) (4.3L VIN W) (Black, 3 Pin) Approximately, 27 cm from main harness in-line to park brake actuator.
C103 (Commercial Van) (5.7L VIN R) (Black, 3 Pin) Approximately, 27 cm from main harness in-line to park brake actuator.
C103 (Commercial Van) (6.5L VIN F) (Black, 3 Pin) Approximately, 10 cm from main harness in-line to park brake actuator.
C103 (Commercial Van) (7.4 VIN J) (Black, 3 Pin) Approximately, 27 cm from main harness in-line to park brake actuator.
C103 (Commercial Van) (7.4 VIN N) (Black, 3 Pin) Approximately, 10 cm from main harness in-line to park brake actuator.
C104 (Commercial Van) (4.3L VIN W) (Black, 2 Pin) Approximately, 27 cm from main harness in-line to park brake actuator.
C104 (Commercial Van) (5.7L VIN R) (Black, 2 Pin) Approximately, 27 cm from main harness in-line to park brake actuator.
C104 (Commercial Van) (6.5L VIN F) (Black, 2 Pin) Approximately, 10 cm from main harness in-line to park brake actuator.
C104 (Commercial Van) (7.4 VIN J) (Black, 2 Pin) Approximately, 27 cm from main harness in-line to park brake actuator.
C104 (Commercial Van) (7.4 VIN N) (Black, 2 Pin) Approximately, 10 cm from main harness in-line to park brake actuator.
C105 (Motor Home) (4.3L VIN W) (Black, 12 Pin) At center of intake manifold.
C105 (Motor Home) (5.7L VIN R) (Black, 16 Pin) At center of intake manifold.
C105 (Motor Home) (7.4L VIN J) At center of intake manifold.
C107 (Black, 10 Pin) Near distributor.
C108 (Black, 8 Pin) Near glow plug control in-line.
C109 (Black, 15 Pin) Approximately, 30 cm from glow plug control breakout, to engine harness.
C112 Near engine oil pressure sender.
C200 (Commercial Van) (Gray, 56 Pin) On driver's island.
C200 (Motor Home) (Black, 4 Pin) Above steering column upper support.
C201 (Commercial Van) (Gray, 11 Pin) On lower steering column.
C201 (Motor Home) (Black, 6 Pin) Above steering column upper support.
C202 (Commercial Van) (Gray, 36 Pin) At left side of firewall, left of steering column.
C202 (Motor Home) (Black, 6 Pin) At base of steering column.
C203 (Commercial Van) (Gray, 36 Pin) At top of steering column support.
C203 (Motor Home) (Gray, 11 Pin) At base of steering column.
C204 (Commercial Van) Near breakout for headlight and dimmer switches.
C204 (Motor Home) In dash harness, 16 cm from daytime running lights module.
C205 (Commercial Van) Near instrument cluster breakout.
C205 (Motor Home) Near dash fuse block.
C206 (Commercial Van) Near daytime running lights module.
C206 (School Bus) Located by body builder.
C207 (Black, 7 Pin) Near battery junction block.
C208 Near dash fuse block.
C300 (Commercial Van) (Black, 15 Pin) Near rear light harness.
C300 (Motor Home) (Black, 7 Pin) Near middle of chassis, at outside of left frame rail.
C400 (Black, 7 Pin) Behind fuel tank, near left frame rail.
C401 (Commercial Van) (Black, 7 Pin) On left frame rail, near rear light harness.
C401 (Motor Home) (Black, 7 Pin) Near left frame rail, near rear of fuel tank.
C402 (Gray, 4 Pin) Center high mount stoplight provision for body builder.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.