1993 GMC Forward Control 7.4 NFACTORY OEM SERVICE PROCEDURE

Electrical Component Locator: Miscellaneous

MISCELLANEOUS LOCATION

Component Location
Blower Motor Resistors On blower motor, in respective front and rear unit.
Data Link Connector (DLC)
"G" Series 4.3L (VIN Z) Below steering column. See Figure.
"P" Series 4.3L (VIN Z - A/T) Below steering column. See Figure.
"P" Series 4.3L (VIN Z - M/T) Below steering column. See Figure.
"G" Series 5.0L (VIN H) & 5.7L (VIN K) Below steering column. See Figure.
"P" Series 5.7L (VIN K - A/T) Below steering column. See Figure.
"P" Series 5.7L (VIN K - M/T) Below steering column. See Figure.
"G" Series 5.7L (VIN K) Below steering column. See Figure.
"G" Series 7.4L (VIN N) Below steering column. See Figure.
"G" Series 7.4L (VIN N) Below steering column. See Figure.
"P" Series 7.4L (VIN N) Below steering column. See Figure.
"G" & "P" Series 6.2L (Diesel) Below steering column. See Figure.
Fuel Heater (Diesel) At fuel filter assembly.
Fuel Pump Test Connector
"G" Series 4.3L (VIN Z) On firewall, near fuel pump relay. See Figure.
"P" Series 4.3L (VIN Z - A/T) On firewall, near fuel pump relay. See Figure.
"P" Series 4.3L (VIN Z - M/T) On firewall, near fuel pump relay. See Figure.
"G" Series 5.0L (VIN H) & 5.7L (VIN K) On firewall, near fuel pump relay. See Figure.
"P" Series 5.7L (VIN K - A/T) On firewall, near fuel pump relay. See Figure.
"P" Series 5.7L (VIN K - M/T) On firewall, near fuel pump relay. See Figure.
"G" Series 5.7L (VIN K) On firewall, near fuel pump relay. See Figure.
"G" Series 7.4L (VIN N) On firewall, near fuel pump relay. See Figure.
"G" Series 7.4L (VIN N) On firewall, near fuel pump relay. See Figure.
"P" Series 7.4L (VIN N) On firewall, near fuel pump relay. See Figure.
Vehicle Speed Sensor (VSS) Buffer
"G" Series 4.3L (VIN Z) Taped to harness, behind instrument panel. See Figure.
"P" Series 4.3L (VIN Z - A/T) Taped to harness, behind instrument panel. See Figure.
"P" Series 4.3L (VIN Z - M/T) Taped to harness, behind instrument panel. See Figure.
"G" Series 5.0L (VIN H) & 5.7L (VIN K) Taped to harness, behind instrument panel. See Figure.
"P" Series 5.7L (VIN K - A/T) Taped to harness, behind instrument panel. See Figure.
"P" Series 5.7L (VIN K - M/T) Taped to harness, behind instrument panel. See Figure.
"G" Series 5.7L (VIN K) Taped to harness, behind instrument panel. See Figure.
"G" Series 7.4L (VIN N) Taped to harness, behind instrument panel. See Figure.
"G" Series 7.4L (VIN N) Taped to harness, behind instrument panel. See Figure.
"P" Series 7.4L (VIN N) Taped to harness, behind instrument panel. See Figure.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.