1979 GMC Forward Control 5.7L Eng VIN L, Standard TransFACTORY OEM SERVICE PROCEDURE

Wheel Alignment

GENERAL MOTORS WHEEL ALIGNMENT SPECIFICATIONS

Application Axle Gap (Inches) (2) Caster (Degrees) Camber (Degrees) Toe-In (Inches) Steering Axis Inclin.
C10 2 1/2 2.4±1.0 0.2±1.7 3\16 .....
  2 3/4 2.1±1.0 0.2±1.7 3/16 .....
  3 1.8±1.0 0.2±1.7 3/16 .....
  3 1/4 1.5±1.0 0.2±1.7 3/16 .....
  3 1/2 1.2±1.0 0.2±1.7 3/16 .....
  3 3/4 1.0±1.0 0.2±1.7 3/16 .....
  4 0.7±1.0 0.2±1.7 3/16 .....
  4 1/4 0.5±1.0 0.2±1.7 3/16 .....
  4 1/2 0.2±1.0 0.2±1.7 3/16 .....
  4 3/4 0.1±1.0 0.2±1.7 3/16 .....
  5 0.3±1.0 0.2±1.7 3/16 .....
C20 & 30 2 1/2 1.5±1.0 0.2±1.7 3/16 .....
  2 3/4 1.2±1.0 0.2±1.7 3/16 .....
  3 0.9±1.0 0.2±1.7 3/16 .....
  3 1/4 0.6±1.0 0.2±1.7 3/16 .....
  3 1/2 0.3±1.0 0.2±1.7 3/16 .....
  3 3/4 0.1±1.0 0.2±1.7 3/16 .....
  4 0±1.0 0.2±1.7 3/16 .....
  4 1/4 -0.1± 1.0 0.2±1.7 3/16 .....
  4 1/2 -0.7±1.0 0.2±1.7 3/16 .....
  4 3/4 -1.0±1.0 0.2±1.7 3/16 .....
  5 -1.2±1.0 0.2±1.7 3/16 .....
K10, 20 & 30 2 1/2 to 5 (3) (4) 0 .....
G10 & 20 1 1/2 2.9±1.0 0.2±0.7 3/16 .....
  1 3/4 2.7±1.0 0.2±0.7 3/16 .....
  2 2.3±1.0 0.2±0.7 3/16 .....
  2 1/4 2.2±1.0 0.2±0.7 3/16 .....
  2 1/2 2.0±1.0 0.2±0.7 3/16 .....
  2 3/4 1.8±1.0 0.2±0.7 3/16 .....
  3 1.6±1.0 0.2±0.7 3/16 .....
  3 1/4 1.4±1.0 0.2±0.7 3/16 .....
  3 1/2 1.3±1.0 0.2±0.7 3/16 .....
  3 3/4 1.1±1.0 0.2±0.7 3/16 .....
  4 0.9±1.0 0.2±0.7 3/16 .....
  4 1/4 0.7±1.0 0.2±0.7 3/16 .....
  G30 1 1/2 3.4±1.0 0.2±0.7 3/16 .....
  1 1/2 3.0±1.0 0.2±0.7 3/16 .....
  2 2.7±1.0 0.2±0.7 3/16 .....
  2 1/4 2.4±1.0 0.2±0.7 3/16 .....
  2 1/2 2.1±1.0 0.2±0.7 3/16 .....
  2 3/4 1.8±1.0 0.2±0.7 3/16 .....
  3 1.5±1.0 0.2±0.7 3/16 .....
  3 1/4 1.3±1.0 0.2±0.7 3/16 .....
  3 1/2 1.0±1.0 0.2±0.7 3/16 .....
  3 3/4 1.1 ±1.0 0.2±0.7 3/16 .....
  4 0.9±1.0 0.2±0.7 3/16 .....
  4 1/4 0.7±1.0 0.2±0.7 3/16 .....
P10 2 1/2 2.3±1.0 0.2±0.7 3/16 .....
  2 3/4 2.0±1.0 0.2±0.7 3/16 .....
  3 1.7±1.0 0.2±0.7 3/16 .....
  3 1/4 1.5±1.0 0.2±0.7 3/16 .....
  3 1/2 1.2±1.0 0.2±0.7 3/16 .....
  3 3/4 0.9±1.0 0.2±0.7 3/16 .....
  4 0.6±1.0 0.2±0.7 3/16 .....
  4 1/4 0.4±1.0 0.2±0.7 3/16 .....
  4/2 0.1±1.0 0.2±0.7 3/16 .....
  4 3/4 -0.1±1.0 0.2±0.7 3/16 .....
  5 -0.3±1.0 0.2±0.7 3/16 .....
P20 & 30 2 2.9±1.0(5)(6) 0.2±0.7 3/16 .....
  2 1/4 2.6±1.0(5)(6) 0.2±0.7 3/16 .....
  2 1/2 2.3±1.0(5)(6) 0.2±0.7 3/16 .....
  2 3/4 2.0±1.0(5)(6) 0.2±0.7 3/16 .....
  3 1.7±1.0(5)(6) 0.2±0.7 3/16 .....
  3 1/4 1.4±1.0(5)(6) 0.2±0.7 3/16 .....
  3 1/2 1.2±1.0(5)(6) 0.2±0.7 3/16 .....
  3 3/4 0.9±1.0(5)(6) 0.2±0.7 3/16 .....
  4 0.6±1.0(5)(6) 0.2±0.7 3/16 .....
  4 1/4 0.4±1.0(5)(6) 0.2±0.7 3/16 .....
  4 1/2 0.2±1.0(5)(6) 0.2±0.7 3/16 .....
  4 3/4 0.1±1.0(5)(6) 0.2±0.7 3/16 .....
P30 MHC 2 1/2 5.5±1.0 0.2±0.7 5/16 .....
  2 3/4 5.3±1.0 0.2±0.7 5/16 .....
  3 5.0±1.0 0.2±0.7 5/16 .....
  3 1/4 4.7±1.0 0.2±0.7 5/16 .....
  3 1/2 4.4±1.0 0.2±0.7 5/16 .....
  3 3/4 4.1±1.0 0.2±0.7 5/16 .....
  4 3.8±1.0 0.2±0.7 5/16 .....
  4 1/4 3.6±1.0 0.2±0.7 5/16 .....
  4 1/2 3.3±1.0 0.2±0.7 5/16 .....
  4 3/4 3.1±1.0 0.2±0.7 5/16 .....
  5 2.9±1.0 0.2±0.7 5/16 .....
(1) The vehicle series and model application in this table has been abbreviated for common reference to both Chevrolet and GMC. Chevrolet models use numerical designations as listed; GMC models use numerical designations as follows; 1500 = 10; 2500 = 20, 3500 = 30.
(2) Axle gap is clearance between jounce bumper and frame.
(3) 8° Caster, no adjustment provision.
(4) 1.0° Camber, no adjustment provision.
(5) Add.3° Caster on vehicles with Hydroboost Brake System.
(6) Subtract.4° Caster on vehicles with Dual Rear Wheels.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.