Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2024 Ford Expedition TimberlineFACTORY OEM SERVICE PROCEDURE
Cruise Control System DTCS: Adaptive
| DTC | Description | Action |
|---|---|---|
| B142E:78 | Forward Looking Sensor Horizontal Alignment: Alignment Or Adjustment Incorrect | GO to Pinpoint Test D |
| B1432:78 | Forward Looking Sensor Vertical Alignment: Alignment Or Adjustment Incorrect | GO to Pinpoint Test D |
| B1433:54 | Forward Looking Sensor Alignment: Missing Calibration | GO to Pinpoint Test D |
| C1A67:96 | Forward Looking Sensor: Component Internal Failure | GO to Pinpoint Test E |
| C1A67:97 | Forward Looking Sensor: Component Or System Operation Obstructed Or Blocked | GO to Pinpoint Test F |
| C1A67:98 | Forward Looking Sensor: Component Or System Over Temperature | GO to Pinpoint Test G |
| U2008:08 | Sensor Cluster: Bus Signal / Message Failure | GO to Pinpoint Test H |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test I |
| U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test I |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test J |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test J |
| U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test J |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test J |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | GO to Pinpoint Test K |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test L |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test M |
| P0504:00 | Brake Switch 'A'/'B' Correlation: No Sub Type Information | GO to Pinpoint Test C |
| P0572:00 | Brake Switch 'A' Circuit Low: No Sub Type Information | GO to Pinpoint Test C |
| P0573:00 | Brake Switch 'A' Circuit High: No Sub Type Information | GO to Pinpoint Test C |
| P1703:00 | Brake Switch Out Of Self Test Range: No Sub Type Information | GO to Pinpoint Test C |
| P1935:00 | Brake Switch/Sensor Signal: No Sub Type Information | GO to Pinpoint Test C |
| B137F:11 | Steering Wheel Left Switch Pack: Circuit Short To Ground | GO to Pinpoint Test B |
| B137F:13 | Steering Wheel Left Switch Pack: Circuit Open | GO to Pinpoint Test B |
| B137F:96 | Steering Wheel Left Switch Pack: Component Internal Failure | GO to Pinpoint Test B |
| B137F:9E | Steering Wheel Left Switch Pack: Stuck On | GO to Pinpoint Test B |
| B1380:11 | Steering Wheel Right Switch Pack: Circuit Short To Ground | GO to Pinpoint Test B |
| B1380:13 | Steering Wheel Right Switch Pack: Circuit Open | GO to Pinpoint Test B |
| B1380:96 | Steering Wheel Right Switch Pack: Component Internal Failure | GO to Pinpoint Test B |
| B1380:9E | Steering Wheel Right Switch Pack: Stuck On | GO to Pinpoint Test B |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.