Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2024 Ford Edge ST-LineFACTORY OEM SERVICE PROCEDURE
Anti-Lock Brake System (Abs) And Stability Control DTCS
| DTC | Description | Action |
|---|---|---|
| B10DF:46 | Master Cylinder Isolation Valve: Calibration/Parameter Memory Failure | GO to Pinpoint Test AL |
| C0001:01 | TCS Control Channel 'A' Valve 1: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0002:01 | TCS Control Channel 'A' Valve 2: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0003:01 | TCS Control Channel 'B' Valve 1: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0004:01 | TCS Control Channel 'B' Valve 2: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0010:01 | Left Front Inlet Control: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0011:01 | Left Front Outlet Control: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0014:01 | Right Front Inlet Control: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0015:01 | Right Front Outlet Control: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0018:01 | Left Rear Inlet Control: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0019:01 | Left Rear Outlet Control: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C001C:01 | Right Rear Inlet Control: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C001D:01 | Right Rear Outlet Control: General Circuit/Electrical Failure | GO to Pinpoint Test R |
| C0020:11 | ABS Pump Motor Control: Circuit Short To Ground | GO to Pinpoint Test G |
| C0020:12 | ABS Pump Motor Control: Circuit Short To Battery | GO to Pinpoint Test G |
| C0020:13 | ABS Pump Motor Control: Circuit Open | GO to Pinpoint Test G |
| C0020:16 | ABS Pump Motor Control: Circuit Voltage Below Threshold | GO to Pinpoint Test G |
| C0020:71 | ABS Pump Motor Control: Actuator Stuck | GO to Pinpoint Test G |
| C0030:07 | Left Front Tone Wheel: Mechanical Failure | GO to Pinpoint Test T |
| C0031:07 | Left Front Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test T |
| C0031:11 | Left Front Wheel Speed Sensor: Circuit Short To Ground | GO to Pinpoint Test I |
| C0031:15 | Left Front Wheel Speed Sensor: Circuit Short To Battery Or Open | GO to Pinpoint Test I |
| C0031:29 | Left Front Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test T |
| C0031:2F | Left Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test T |
| C0031:4A | Left Front Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test AD |
| C0031:64 | Left Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test T |
| C0033:07 | Right Front Tone Wheel: Mechanical Failure | GO to Pinpoint Test T |
| C0034:07 | Right Front Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test T |
| C0034:11 | Right Front Wheel Speed Sensor: Circuit Short To Ground | GO to Pinpoint Test I |
| C0034:15 | Right Front Wheel Speed Sensor: Circuit Short To Battery Or Open | GO to Pinpoint Test I |
| C0034:29 | Right Front Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test T |
| C0034:2F | Right Front Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test T |
| C0034:4A | Right Front Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test AD |
| C0034:64 | Right Front Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test T |
| C0036:07 | Left Rear Tone Wheel: Mechanical Failure | GO to Pinpoint Test T |
| C0037:07 | Left Rear Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test T |
| C0037:11 | Left Rear Wheel Speed Sensor: Circuit Short To Ground | GO to Pinpoint Test J |
| C0037:15 | Left Rear Wheel Speed Sensor: Circuit Short To Battery Or Open | GO to Pinpoint Test J |
| C0037:29 | Left Rear Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test T |
| C0037:2F | Left Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test T |
| C0037:4A | Left Rear Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test AD |
| C0037:64 | Left Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test T |
| C0039:07 | Right Rear Tone Wheel: Mechanical Failure | GO to Pinpoint Test T |
| C003A:07 | Right Rear Wheel Speed Sensor: Mechanical Failure | GO to Pinpoint Test T |
| C003A:11 | Right Rear Wheel Speed Sensor: Circuit Short To Ground | GO to Pinpoint Test J |
| C003A:15 | Right Rear Wheel Speed Sensor: Circuit Short To Battery Or Open | GO to Pinpoint Test J |
| C003A:29 | Right Rear Wheel Speed Sensor: Signal Invalid | GO to Pinpoint Test T |
| C003A:2F | Right Rear Wheel Speed Sensor: Signal Erratic | GO to Pinpoint Test T |
| C003A:4A | Right Rear Wheel Speed Sensor: Incorrect Component Installed | GO to Pinpoint Test AD |
| C003A:64 | Right Rear Wheel Speed Sensor: Signal Plausibility Failure | GO to Pinpoint Test T |
| C0040:64 | Brake Pedal Switch 'A': Signal Plausibility Failure | GO to Pinpoint Test U |
| C0044:28 | Brake Pressure Sensor 'A': Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test U |
| C0044:47 | Brake Pressure Sensor 'A': Watchdog/Safety μC Failure | GO to Pinpoint Test AE |
| C0044:49 | Brake Pressure Sensor 'A': Internal Electronic Failure | GO to Pinpoint Test AE |
| C0044:51 | Brake Pressure Sensor 'A': Not Programmed | GO to Pinpoint Test AE |
| C0044:64 | Brake Pressure Sensor 'A': Signal Plausibility Failure | GO to Pinpoint Test AE |
| C0044:8F | Brake Pressure Sensor 'A': Erratic | GO to Pinpoint Test AE |
| C0047:01 | Brake Booster Pressure Sensor: General Circuit/Electrical Failure | GO to Pinpoint Test B |
| C0047:26 | Brake Booster Pressure Sensor: Signal Rate Of Change Below Threshold | GO to Pinpoint Test B |
| C0047:27 | Brake Booster Pressure Sensor: Signal Rate Of Change Above Threshold | GO to Pinpoint Test B |
| C0051:62 | Steering Wheel Position Sensor: Signal Compare Failure | GO to Pinpoint Test L |
| C0051:62 | Steering Wheel Position Sensor: Signal Compare Failure | GO to Pinpoint Test M |
| C0051:64 | Steering Wheel Position Sensor: Signal Plausibility Failure | GO to Pinpoint Test L |
| C0051:64 | Steering Wheel Position Sensor: Signal Plausibility Failure | GO to Pinpoint Test M |
| C0051:67 | Steering Wheel Position Sensor: Signal Incorrect After Event | GO to Pinpoint Test L |
| C0051:67 | Steering Wheel Position Sensor: Signal Incorrect After Event | GO to Pinpoint Test M |
| C0051:85 | Steering Wheel Position Sensor: Signal Above Allowable Range | GO to Pinpoint Test L |
| C0051:85 | Steering Wheel Position Sensor: Signal Above Allowable Range | GO to Pinpoint Test M |
| C0061:28 | Lateral Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test AJ |
| C0061:2F | Lateral Acceleration Sensor: Signal Erratic | GO to Pinpoint Test AJ |
| C0061:64 | Lateral Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test AJ |
| C0062:28 | Longitudinal Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test AJ |
| C0062:54 | Longitudinal Acceleration Sensor: Missing Calibration | GO to Pinpoint Test AF |
| C0062:54 | Longitudinal Acceleration Sensor: Missing Calibration | GO to Pinpoint Test AJ |
| C0062:64 | Longitudinal Acceleration Sensor: Signal Plausibility Failure | GO to Pinpoint Test AJ |
| C0062:76 | Longitudinal Acceleration Sensor: Wrong Mounting Position | GO to Pinpoint Test AK |
| C0063:28 | Yaw Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure | GO to Pinpoint Test AJ |
| C0063:2F | Yaw Rate Sensor: Signal Erratic | GO to Pinpoint Test AJ |
| C0063:64 | Yaw Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test AJ |
| C0064:64 | Roll Rate Sensor: Signal Plausibility Failure | GO to Pinpoint Test AJ |
| C006B:00 | Stability System Active Too Long: No Sub Type Information | GO to Pinpoint Test V |
| C1015:08 | Vacuum Supply: Bus Signal / Message Failure | GO to Pinpoint Test B |
| C1015:7A | Vacuum Supply: Fluid Leak Or Seal Failure | GO to Pinpoint Test Z |
| C1015:7B | Vacuum Supply: Low Fluid Level | GO to Pinpoint Test Z |
| C1020:00 | Brake System Fill Not Complete: No Sub Type Information | GO to Pinpoint Test P |
| C1020:52 | Brake System Fill Not Complete: Not Activated | GO to Pinpoint Test P |
| C1109:64 | Vehicle Dynamics Control Switch: Signal Plausibility Failure | GO to Pinpoint Test K |
| C1A08:1C | Pressure Sensor Supply: Circuit Voltage Out Of Range | GO to Pinpoint Test AE |
| C1B14:11 | Sensor Supply Voltage A: Circuit Short To Ground | GO to Pinpoint Test B |
| C1B14:12 | Sensor Supply Voltage A: Circuit Short To Battery | GO to Pinpoint Test B |
| C1B15:1C | Sensor Supply Voltage B: Circuit Voltage Out Of Range | GO to Pinpoint Test B |
| P0942:46 | Hydraulic Pressure Unit: Calibration/Parameter Memory Failure | GO to Pinpoint Test AL |
| P0942:49 | Hydraulic Pressure Unit: Internal Electronic Failure | GO to Pinpoint Test AL |
| P193B:00 | Throttle/Pedal Signal: No Sub Type Information | GO to Pinpoint Test AR |
| U0100:00 | Lost Communication With ECM/PCM 'A': No Sub Type Information | GO to Pinpoint Test AA |
| U0103:00 | Lost Communication With Gear Shift Control Module A: No Sub Type Information | GO to Pinpoint Test H |
| U011D:00 | Lost Communication With All Wheel Drive Control Module: No Sub Type Information | GO to Pinpoint Test AG |
| U0126:00 | Lost Communication With Steering Angle Sensor Module: No Sub Type Information | GO to Pinpoint Test AM |
| U0131:00 | Lost Communication With Power Steering Control Module 'A': No Sub Type Information | GO to Pinpoint Test W |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test C |
| U0146:87 | Lost Communication With Serial Data Gateway 'A': Missing Message | GO to Pinpoint Test AC |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AQ |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test AQ |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AI |
| U0256:00 | Lost Communication With Front Controls Interface Module 'A': No Sub Type Information | GO to Pinpoint Test AN |
| U0265:00 | Lost Communication with Image Processing Sensor 'A': No Sub Type Information | GO to Pinpoint Test O |
| U0300:51 | Internal Control Module Software Incompatibility: Not Programmed | GO to Pinpoint Test S |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test AA |
| U0401:86 | Invalid Data Received from ECM/PCM A: Signal Invalid | GO to Pinpoint Test AA |
| U0404:86 | Invalid Data Received from Gear Shift Control Module A: Signal Invalid | GO to Pinpoint Test H |
| U0405:86 | Invalid Data Received From Cruise Control Module: Signal Invalid | GO to Pinpoint Test N |
| U0420:00 | Invalid Data Received from Power Steering Control Module 'A': No Sub Type Information | GO to Pinpoint Test W |
| U0420:83 | Invalid Data Received from Power Steering Control Module 'A': Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test W |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test C |
| U0428:82 | Invalid Data Received From Steering Angle Sensor Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AM |
| U0428:83 | Invalid Data Received From Steering Angle Sensor Module: Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test AM |
| U0429:82 | Invalid Data Received From Steering Column Control Module: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test AO |
| U0429:86 | Invalid Data Received From Steering Column Control Module: Signal Invalid | GO to Pinpoint Test AO |
| U0452:29 | Invalid Data Received From Restraints Control Module: Signal Invalid | GO to Pinpoint Test AQ |
| U0452:83 | Invalid Data Received From Restraints Control Module: Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test AQ |
| U0452:86 | Invalid Data Received From Restraints Control Module: Signal Invalid | GO to Pinpoint Test AQ |
| U053B:82 | Invalid Data Received From Image Processing Module A: Alive/Sequence Counter Incorrect/Not Updated | GO to Pinpoint Test O |
| U053B:83 | Invalid Data Received From Image Processing Module A: Value Of Signal Protection Calculation Incorrect | GO to Pinpoint Test O |
| U0557:86 | Invalid Data Received From Front Controls Interface Module 'A': Signal Invalid | GO to Pinpoint Test AN |
| U2001:00 | Reduced System Function: No Sub Type Information | GO to Pinpoint Test F |
| U2007:46 | Valve(s): Calibration/Parameter Memory Failure | GO to Pinpoint Test AL |
| U2007:62 | Valve(s): Signal Compare Failure | GO to Pinpoint Test AL |
| U2017:57 | Control Module Software #2: Invalid/Incompatible Software Component | GO to Pinpoint Test S |
| U2017:93 | Control Module Software #2: No Operation | GO to Pinpoint Test S |
| U2024:51 | Control Module Cal-Config Data: Not Programmed | GO to Pinpoint Test S |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test S |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test S |
| U2107:00 | Collision Mitigation By Braking: No Sub Type Information | GO to Pinpoint Test N |
| U2107:68 | Collision Mitigation By Braking: Event Information | GO to Pinpoint Test AH |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test S |
| U3000:47 | Control Module: Watchdog/Safety μC Failure | GO to Pinpoint Test R |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test R |
| U3000:96 | Control Module: Component Internal Failure | GO to Pinpoint Test R |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | GO to Pinpoint Test X |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test A |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test E |
| U3003:1C | Battery Voltage: Circuit Voltage Out Of Range | GO to Pinpoint Test A |
| U300A:29 | Ignition Switch: Signal Invalid | GO to Pinpoint Test A |
| P0555:00 | Brake Booster Pressure Sensor Circuit: No Sub Type Information | GO to Pinpoint Test B |
| P0556:00 | Brake Booster Pressure Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| P0557:00 | Brake Booster Pressure Sensor Circuit Low: No Sub Type Information | GO to Pinpoint Test B |
| P0558:00 | Brake Booster Pressure Sensor Circuit High: No Sub Type Information | GO to Pinpoint Test B |
| P0559:00 | Brake Booster Pressure Sensor Circuit Intermittent: No Sub Type Information | GO to Pinpoint Test B |
| P05FF:00 | Brake Pressure Sensor / Brake Pedal Position Sensor Correlation: No Sub Type Information | GO to Pinpoint Test B |
| P103C:00 | Aspirator Valve Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test AP |
| P103D:00 | Aspirator Valve Control Circuit Low: No Sub Type Information | GO to Pinpoint Test AP |
| P103E:00 | Aspirator Valve Control Circuit High: No Sub Type Information | GO to Pinpoint Test AP |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.