Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2024 Ford Edge ST-LineFACTORY OEM SERVICE PROCEDURE
Common Specifications & Procedures
EDGE COMMON SPECIFICATIONS & PROCEDURES
| System | Specifications/Procedures | |||
|---|---|---|---|---|
| Air Conditioning | ||||
| Service | SPECIFICATIONS | |||
| Torque | Refer to the appropriate component in REMOVAL AND INSTALLATION . | |||
| Axle Nut/Hub Nut | ||||
| Torque | 148 lb.ft (200 Nm) | |||
| Battery | SPECIFICATIONS | |||
| Brakes | ||||
| Bleeding Sequence | RR, LR, RF, LF BRAKE SYSTEM PRESSURE BLEEDING |
|||
| Front Disc Brakes w/Torque | Refer to appropriate component in REMOVAL AND INSTALLATION | |||
| Rear Disc Brakes w/Torque | Refer to appropriate component in REMOVAL AND INSTALLATION | |||
| Charging | ||||
| Generator w/Torque | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | Generator Bolt: 18 lb.ft (25 Nm) | |||
| 2.7L EcoBoost (238kW/324PS) | Generator Bolt and Stud Nut: 35 lb.ft (47 Nm) Generator Stud: 71 lb.in (8 Nm) |
|||
| Drive Belts | ||||
| Adjustment | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | ACCESSORY DRIVE BELT | |||
| 2.7L EcoBoost (238kW/324PS) | ACCESSORY DRIVE BELT | |||
| Belt Routing | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | ACCESSORY DRIVE - COMPONENT LOCATION | |||
| 2.7L EcoBoost (238kW/324PS) | ACCESSORY DRIVE - COMPONENT LOCATION | |||
| Engine Cooling | ||||
| General Service Specifications | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | SPECIFICATIONS | |||
| 2.7L EcoBoost (238kW/324PS) | SPECIFICATIONS | |||
| Radiator Cap Pressure | 145 kPa (21 psi) |
|||
| Radiator Pressure Test (Removed From The Vehicle) | 138 kPa (20 psi) | |||
| Thermostat R & I | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | THERMOSTAT | |||
| 2.7L EcoBoost (238kW/324PS) | THERMOSTAT | |||
| Water Pump R & I | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | COOLANT PUMP | |||
| 2.7L EcoBoost (238kW/324PS) | COOLANT PUMP | |||
| Engine Mechanical | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | ||||
| Compression | SPECIFICATIONS | |||
| Oil pressure at 1, 500 rpm with engine oil temperature between 121.9 - 175.9°F (50 - 80°C) | 27.6 - 37.7 psi (190 - 260 kPa) | |||
| Overhaul | SPECIFICATIONS | |||
| Torque | Refer to the appropriate procedure in REMOVAL AND INSTALLATION | |||
| 2.7L EcoBoost (238kW/324PS) | ||||
| Compression | SPECIFICATIONS | |||
| Oil Pressure Reading 1 (Minimum average oil pressure at 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park.) | 21 psi (144.8 kPa) | |||
| Oil Pressure Reading 2 (Minimum average oil pressure at 2, 000 rpm after 15 secs with engine at normal operating temperature and transmission in Park (Oil Pressure Control Solenoid connector disconnected)) | Reading 1 value plus 8 psi (55.1 kPa) | |||
| Overhaul | SPECIFICATIONS | |||
| Torque | Refer to appropriate component in REMOVAL AND INSTALLATION (1 OF 2) and REMOVAL AND INSTALLATION (2 OF 2) | |||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | |||
| Flywheel/Flex Plate Torque | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | For tightening sequence, refer to FLEXPLATE
. Stage 1: 37 lb.ft (50 Nm) Stage 2: 59 lb.ft (80 Nm) Stage 3: 83 lb.ft (112 Nm) |
|||
| 2.7L EcoBoost (238kW/324PS) | For Tightening Sequence Refer to FLEXPLATE 59 lb.ft (80 Nm) |
|||
| Fuel System | ||||
| Fuel Filter Location | Located in fuel tank as part of Fuel Pump Module. | |||
| Fuel Filter R & I | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | FUEL PUMP AND SENDER UNIT | |||
| 2.7L EcoBoost (238kW/324PS) | FUEL PUMP AND SENDER UNIT | |||
| Pressure Release Procedure | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | FUEL SYSTEM PRESSURE RELEASE | |||
| 2.7L EcoBoost (238kW/324PS) | FUEL SYSTEM PRESSURE RELEASE | |||
| Pressure Specification | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | SPECIFICATIONS | |||
| 2.7L EcoBoost (238kW/324PS) | SPECIFICATIONS | |||
| Fuel Pressure Test Procedure | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | FUEL SYSTEM PRESSURE CHECK | |||
| 2.7L EcoBoost (238kW/324PS) | FUEL SYSTEM PRESSURE CHECK | |||
| Ignition | ||||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | |||
| Ignition Wires (Routing) | Engines are equipped with Coil-on-plug ignition. | |||
| Spark Plugs | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | ||||
| Type | CYFS-12Y-RT3 | |||
| Gap | 0.030 In. (0.75 mm) | |||
| Torque | 106 In. Lbs. (12 N.m) | |||
| 2.7L EcoBoost (238kW/324PS) | ||||
| Type | CYFS-12Y-RT3 | |||
| Gap | 0.028-0.031 in (0.7-0.8 mm) | |||
| Torque | 133 In. Lbs. (15 N.m) | |||
| Starting | ||||
| Starter | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | SPECIFICATIONS | |||
| 2.7L EcoBoost (238kW/324PS) | SPECIFICATIONS | |||
| Torque | ||||
| 2.0L EcoBoost (184kW/250PS) - MI4 | For removal and installation, refer to STARTER MOTOR . | |||
| 2.7L EcoBoost (238kW/324PS) | For removal and installation, refer to STARTER MOTOR . | |||
| Wheel Alignment | ||||
| Adjustment Specifications | SPECIFICATIONS | |||
| Torque | Refer to the appropriate procedure in GENERAL PROCEDURES | |||
| Wheel & Tire | ||||
| Wheel Lug Nut Torque | For tightening sequence, refer to WHEEL AND TIRE 162 lb.ft (220 Nm) |
|||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.