Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Module Configuration and Parameter Chart
The chart describes specific module configuration information:
| Module Name | Module Address | Programmable Module Installation (PMI) Available | Reprogram/Flash Capable | Requires Adaptive Learning or Calibration | Available Programmable Parameters |
|---|---|---|---|---|---|
| ABS module | 760 | Yes | Yes | ABS calibration Brake system pressure bleeding |
None |
| ACCM | 7C7 | No | No | No | None |
| ACM | 727 | Yes | Yes | No | None |
| APIM | 7D0 | Yes | Yes (diagnostic scan tool and USB flash drive) | No | None |
| BCM | 726 | Yes | Yes | PATS key programming PATS parameter reset CEI BMS reset If equipped with rear video parking aid, BCMLIN initialization TPMS training |
Trailer tow |
| BCMC [ BJB ] | 6F0 | Yes | Yes | No | None |
| BECM | 7E4 | Yes | Yes | No | None |
| BECMB | 723 | Yes | Yes | SRS prove out | None |
| CCM | 764 | Yes | Yes | CCM radar alignment | None |
| Driver Status Monitor Camera Module [CMR ] | 7C1 | Yes | Yes | No | None |
| DCDC | 746 | Yes | Yes | No | None |
| DCME | 7A2 | Yes | Yes | No | None |
| DCMF | 762 | Yes | Yes | No | None |
| DCMG | 7B3 | Yes | Yes | No | None |
| DCMH | 7B4 | Yes | Yes | No | None |
| DDM | 740 | Yes | Yes | Windows initialization | None |
| DSM | 744 | Yes | Yes | No | None |
| DSP | 783 | Yes | Yes | No | None |
| GFM (Front Trunk Release Module (FTRM)) | 7A1 | Yes | Yes | No | None |
| GSM | 732 | Yes | Yes | No | None |
| GWM | 716 | Yes | Yes (diagnostic scan tool and USB flash drive) | No | None |
| HCM | 734 | Yes | Yes | HCM calibration | None |
| HVAC module | 733 | Yes | Yes | No | None |
| IPC | 720 | Yes | Yes (diagnostic scan tool and USB flash drive) | No | None |
| IPMA | 706 | Yes | Yes (diagnostic scan tool and USB flash drive) | No | Trailer tow |
| OBCC | 6F5 | No | No | No | None |
| OCS module | 765 | No | No | OCSM re-zero | None |
| PACM | 750 | No | No | No | None |
| PCM | 7E0 | Yes | Yes | PATS parameter reset | None |
| PDM | 741 | Yes | Yes | Window initialization | None |
| PSCM | 730 | Yes | Yes | No | None |
| RCM | 737 | Yes | Yes | ABS calibration service functions | None |
| RFA | 731 | Yes | Yes | PATS module initialization Secure code unlock |
None |
| RGTM | 775 | Yes | Yes | No | None |
| SCCM | 724 | Yes | Yes | No | None |
| SOBDM (Battery Charging Control Module [BCCM]) | 7E2 | Yes | Yes | No | None |
| SOBDMB | 7E7 | Yes | Yes | No | None |
| SOBDMC | 7E6 | Yes | Yes | No | None |
| SODCMC | 6F2 | Yes | Yes | No | None |
| SODCMD | 6F3 | Yes | Yes | No | None |
| SODL | 7C4 | Yes | Yes | No | None |
| SODR | 7C6 | Yes | Yes | No | None |
| TCU | 754 | Yes | Yes (diagnostic scan tool and USB flash drive) | No | None |
| VDM | 721 | Yes | Yes | Height sensor calibration | None |
| WACM | 725 | Yes | Yes | No | None |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.