Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2022 Ford Expedition TimberlineFACTORY OEM SERVICE PROCEDURE
Side And Rear Vision System DTCS
| DTC | Description | Action |
|---|---|---|
| B118C:11 | Left Blind Spot Warning Indicator: Circuit Short To Ground | GO to Pinpoint Test D |
| B118C:15 | Left Blind Spot Warning Indicator: Circuit Short To Battery Or Open | GO to Pinpoint Test C |
| B118C:15 | Left Blind Spot Warning Indicator: Circuit Short To Battery Or Open | GO to Pinpoint Test D |
| B15EC:14 | Side Obstacle Detector "A": Circuit Short To Ground Or Open | GO to Pinpoint Test S |
| B15EC:15 | Side Obstacle Detector "A": Circuit Short To Battery Or Open | GO to Pinpoint Test S |
| B15ED:14 | Side Obstacle Detector "B": Circuit Short To Ground Or Open | GO to Pinpoint Test T |
| B15ED:15 | Side Obstacle Detector "B": Circuit Short To Battery Or Open | GO to Pinpoint Test T |
| B118D:11 | Right Blind Spot Warning Indicator: Circuit Short To Ground | GO to Pinpoint Test D |
| B118D:15 | Right Blind Spot Warning Indicator: Circuit Short To Battery Or Open | GO to Pinpoint Test C |
| B118D:15 | Right Blind Spot Warning Indicator: Circuit Short To Battery Or Open | GO to Pinpoint Test D |
| B13F3:54 | Left Rear Side Sensor: Missing Calibration | GO to Pinpoint Test I |
| B13F3:96 | Left Rear Side Sensor: Component Internal Failure | GO to Pinpoint Test J |
| B13F3:97 | Left Rear Side Sensor: Component Or System Operation Obstructed Or Blocked | GO to Pinpoint Test K |
| B13F3:98 | Left Rear Side Sensor: Component Or System Over Temperature | GO to Pinpoint Test L |
| B15D9:78 | Left Rear Side Sensor Horizontal Alignment: Alignment Or Adjustment Incorrect | GO to Pinpoint Test I |
| B15DD:78 | Left Rear Side Sensor Vertical Alignment: Alignment Or Adjustment Incorrect | GO to Pinpoint Test I |
| U2008:08 | Sensor Cluster: Bus Signal/Message Failures | GO to Pinpoint Test M |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test N |
| U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test N |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test O |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test O |
| U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test O |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test O |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | GO to Pinpoint Test P |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test Q |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test R |
| B13F4:54 | Right Rear Side Sensor: Missing Calibration | GO to Pinpoint Test I |
| B13F4:96 | Right Rear Side Sensor: Component Internal Failure | GO to Pinpoint Test J |
| B13F4:97 | Right Rear Side Sensor: Component Or System Operation Obstructed Or Blocked | GO to Pinpoint Test K |
| B13F4:98 | Right Rear Side Sensor: Component Or System Over Temperature | GO to Pinpoint Test L |
| B157D:78 | Right Rear Side Sensor Vertical Alignment: Alignment Or Adjustment Incorrect | GO to Pinpoint Test I |
| B159C:78 | Right Rear Side Sensor Horizontal Alignment: Alignment Or Adjustment Incorrect | GO to Pinpoint Test I |
| U2008:08 | Sensor Cluster: Bus Signal/Message Failures | GO to Pinpoint Test M |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test N |
| U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test N |
| U3000:41 | Control Module: General Checksum Failure | GO to Pinpoint Test O |
| U3000:42 | Control Module: General Memory Failure | GO to Pinpoint Test O |
| U3000:44 | Control Module: Data Memory Failure | GO to Pinpoint Test O |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test O |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | GO to Pinpoint Test P |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test Q |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test R |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.