Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2022 Ford Expedition TimberlineFACTORY OEM SERVICE PROCEDURE
Front Seats: SCMH
| DTC | Description | Action |
|---|---|---|
| B146F:00 | Back Bladder System Electropneumatic Failure: No Sub Type Information | GO to Pinpoint Test G |
| B146F:04 | Back Bladder System Electropneumatic Failure: System Internal Failure | GO to Pinpoint Test G |
| B1470:00 | Cushion Bladder System Electropneumatic Failure: No Sub Type Information | GO to Pinpoint Test G |
| B1470:04 | Cushion Bladder System Electropneumatic Failure: System Internal Failure | GO to Pinpoint Test G |
| B1471:11 | Multi-Contour Seat Switch Input: Circuit Short To Ground | GO to Pinpoint Test G |
| B1471:13 | Multi-Contour Seat Switch Input: Circuit Open | GO to Pinpoint Test G |
| B1471:2A | Multi-Contour Seat Switch Input: Signal Stuck In Range | VERIFY there is no obstruction that may be causing the multi-contour seat switch to be stuck in a certain position. If OK, INSTALL a new seat control switch. REFER to: Front Seat Control Switch |
| B1473:11 | Pump Driver: Circuit Short To Ground | GO to Pinpoint Test G |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test S |
| U0208:00 | Lost Communication With "Seat Control Module A": No Sub Type Information | GO to Pinpoint Test T |
| U024B:00 | Lost Communication with Seat Control Module "G": No Sub Type Information | GO to Pinpoint Test U |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test V |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | GO to Pinpoint Test W |
| U0455:00 | Invalid Data Received From Restraints Occupant Classification System Module: No Sub Type Information | GO to Pinpoint Test X |
| U1000:00 | Solid State Driver Protection Activated - Driver Disabled: No Sub Type Information | DIAGNOSE any other related SCMH Diagnostic Trouble Codes (DTCs) first. CLEAR the Diagnostic Trouble Codes (DTCs). REPEAT the self-test. If DTC U1000:00 returns. INSTALL a new SCMH. REFER to: Driver Multi-Contour Seat Module [SCMG] |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information |
NOTE:
This DTC indicates PMI has not been done to a newly installed module or configuration data has been lost. Using a diagnostic scan tool, CARRY OUT PMI on the SCMH. REPEAT the self-test and VERIFY successful PMI. CLEAR the Diagnostic Trouble Codes (DTCs). |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new SCMH. REFER to: Driver Multi-Contour Seat Module [SCMG] |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.