2022 Ford Bronco Sport BaseFACTORY OEM SERVICE PROCEDURE

Anti-Lock Brake System And Stability Control DTCS

Diagnostics in this service information assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .

DTC Description Action
C0020:11 ABS Pump Motor Control: Circuit Short To Ground GO to Pinpoint Test H
C0020:12 ABS Pump Motor Control: Circuit Short To Battery GO to Pinpoint Test H
C0020:13 ABS Pump Motor Control: Circuit Open GO to Pinpoint Test H
C0020:49 ABS Pump Motor Control: Internal Electronic Failure GO to Pinpoint Test H
C0020:71 ABS Pump Motor Control: Actuator Stuck GO to Pinpoint Test H
C0030:07 Left Front Tone Wheel: Mechanical Failures GO to Pinpoint Test AB
C0031:01 Left Front Wheel Speed Sensor: General Electrical Failure GO to Pinpoint Test M
C0031:07 Left Front Wheel Speed Sensor: Mechanical Failures GO to Pinpoint Test AB
C0031:2F Left Front Wheel Speed Sensor: Signal Erratic GO to Pinpoint Test AB
C0031:4A Left Front Wheel Speed Sensor: Incorrect Component Installed GO to Pinpoint Test AL
C0031:64 Left Front Wheel Speed Sensor: Signal Plausibility Failure GO to Pinpoint Test AB
C0033:07 Right Front Tone Wheel: Mechanical Failures GO to Pinpoint Test AB
C0034:01 Right Front Wheel Speed Sensor: General Electrical Failure GO to Pinpoint Test M
C0034:07 Right Front Wheel Speed Sensor: Mechanical Failures GO to Pinpoint Test AB
C0034:2F Right Front Wheel Speed Sensor: Signal Erratic GO to Pinpoint Test AB
C0034:4A Right Front Wheel Speed Sensor: Incorrect Component Installed GO to Pinpoint Test AL
C0034:64 Right Front Wheel Speed Sensor: Signal Plausibility Failure GO to Pinpoint Test AB
C0036:07 Left Rear Tone Wheel: Mechanical Failures GO to Pinpoint Test AB
C0037:01 Left Rear Wheel Speed Sensor: General Electrical Failure GO to Pinpoint Test N
C0037:07 Left Rear Wheel Speed Sensor: Mechanical Failures GO to Pinpoint Test AB
C0037:2F Left Rear Wheel Speed Sensor: Signal Erratic GO to Pinpoint Test AB
C0037:4A Left Rear Wheel Speed Sensor: Incorrect Component Installed GO to Pinpoint Test AL
C0037:64 Left Rear Wheel Speed Sensor: Signal Plausibility Failure GO to Pinpoint Test AB
C0039:07 Right Rear Tone Wheel: Mechanical Failures GO to Pinpoint Test AB
C003A:01 Right Rear Wheel Speed Sensor: General Electrical Failure GO to Pinpoint Test N
C003A:07 Right Rear Wheel Speed Sensor: Mechanical Failures GO to Pinpoint Test AB
C003A:2F Right Rear Wheel Speed Sensor: Signal Erratic GO to Pinpoint Test AB
C003A:4A Right Rear Wheel Speed Sensor: Incorrect Component Installed GO to Pinpoint Test AL
C003A:64 Right Rear Wheel Speed Sensor: Signal Plausibility Failure GO to Pinpoint Test AB
C0040:64 Brake Pedal Switch "A": Signal Plausibility Failure GO to Pinpoint Test AC
C0044:49 Brake Pressure Sensor "A": Internal Electronic Failure GO to Pinpoint Test AM
C0044:64 Brake Pressure Sensor "A": Signal Plausibility Failure GO to Pinpoint Test AM
C0044:8F Brake Pressure Sensor "A": Erratic GO to Pinpoint Test AM
C0047:1C Brake Booster Pressure Sensor: Circuit Voltage Out Of Range GO to Pinpoint Test CO
C0047:64 Brake Booster Pressure Sensor: Signal Plausibility Failure GO to Pinpoint Test CO
C0049:01 Brake Fluid Level: General Electrical Failure GO to Pinpoint Test T
C0049:7A Brake Fluid Level: Fluid Leak Or Seal Failure GO to Pinpoint Test T
C0049:7B Brake Fluid Level: Low Fluid Level GO to Pinpoint Test T
C0051:64 Steering Wheel Position Sensor: Signal Plausibility Failure GO to Pinpoint Test LA
C0051:67 Steering Wheel Position Sensor: Signal Incorrect After Event GO to Pinpoint Test LA
C0051:85 Steering Wheel Position Sensor: Signal Above Allowable Range GO to Pinpoint Test LA
C0051:86 Steering Wheel Position Sensor: Signal Invalid GO to Pinpoint Test LA
C0061:28 Lateral Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure GO to Pinpoint Test BH
C0061:54 Lateral Acceleration Sensor: Missing Calibration GO to Pinpoint Test AN
C0061:64 Lateral Acceleration Sensor: Signal Plausibility Failure GO to Pinpoint Test BH
C0062:28 Longitudinal Acceleration Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure GO to Pinpoint Test BH
C0062:54 Longitudinal Acceleration Sensor: Missing Calibration GO to Pinpoint Test AN
C0062:64 Longitudinal Acceleration Sensor: Signal Plausibility Failure GO to Pinpoint Test BH
C0063:28 Yaw Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure GO to Pinpoint Test BH
C0063:64 Yaw Rate Sensor: Signal Plausibility Failure GO to Pinpoint Test BH
C0064:28 Roll Rate Sensor: Signal Bias Level Out Of Range/Zero Adjustment Failure GO to Pinpoint Test BH
C0064:64 Roll Rate Sensor: Signal Plausibility Failure GO to Pinpoint Test BH
C006A:95 Multi-axis Acceleration Sensor: Incorrect Assembly GO to Pinpoint Test AN
C006B:00 Stability System Active Too Long: No Sub Type Information GO to Pinpoint Test AD
C0078:00 Tire Diameter: No Sub Type Information GO to Pinpoint Test ZA
C052E:A2 ABS Pump Motor Control Circuit Low: System Voltage Low GO to Pinpoint Test H
C0594:12 Brake Booster Motor "A" Performance: Circuit Short To Battery GO to Pinpoint Test CP
C0594:78 Brake Booster Motor "A" Performance: Alignment Or Adjustment Incorrect GO to Pinpoint Test CP
C0594:92 Brake Booster Motor "A" Performance: Performance Or Incorrect Operation GO to Pinpoint Test CP
C0596:00 Brake Booster Motor "A" Current Sensor Circuit Range/Performance: No Sub Type Information GO to Pinpoint Test CP
C1013:09 Brake System Pressure: Component Failures GO to Pinpoint Test CO
C1013:7A Brake System Pressure: Fluid Leak Or Seal Failure GO to Pinpoint Test CO
C1013:7C Brake System Pressure: Slow Response GO to Pinpoint Test CO
C1013:92 Brake System Pressure: Performance Or Incorrect Operation GO to Pinpoint Test CO
C1019:29 Linear Actuator Control (LAC): Signal Invalid GO to Pinpoint Test CO
C1019:74 Linear Actuator Control (LAC): Actuator Slipping GO to Pinpoint Test CO
C1019:78 Linear Actuator Control (LAC): Alignment Or Adjustment Incorrect GO to Pinpoint Test CO
C1019:92 Linear Actuator Control (LAC): Performance Or Incorrect Operation GO to Pinpoint Test CO
C101F:46 Generic Valve Failure: Calibration/Parameter Memory Failure GO to Pinpoint Test Z
C101F:49 Generic Valve Failure: Internal Electronic Failure GO to Pinpoint Test Z
C1020:00 Brake System Fill Not Complete: No Sub Type Information GO to Pinpoint Test W
C1020:52 Brake System Fill Not Complete: Not Activated GO to Pinpoint Test W
C1A08:1C Pressure Sensor Supply: Circuit Voltage Out Of Range GO to Pinpoint Test AM
C1B11:71 Pressure Control Valve: Actuator Stuck GO to Pinpoint Test Y
P0562:16 System Voltage Low: Circuit Voltage Below Threshold GO to Pinpoint Test A
P0563:17 System Voltage High: Circuit Voltage Above Threshold GO to Pinpoint Test F
P05D3:86 Driver Mode Select Switch "A" Range/Performance: Signal Invalid GO to Pinpoint Test BM
U0100:00 Lost Communication With ECM/PCM "A": No Sub Type Information GO to Pinpoint Test AI
U0103:00 Lost Communication With Gear Shift Control Module A: No Sub Type Information GO to Pinpoint Test AV
U0131:00 Lost Communication With Power Steering Control Module "A": No Sub Type Information GO to Pinpoint Test AE
U0140:00 Lost Communication With Body Control Module: No Sub Type Information GO to Pinpoint Test D
U0151:00 Lost Communication With Restraints Control Module: No Sub Type Information GO to Pinpoint Test BH
U0155:00 Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information GO to Pinpoint Test AR
U0164:00 Lost Communication With HVAC Control Module: No Sub Type Information GO to Pinpoint Test CE
U023A:00 Lost Communication With Image Processing Module A: No Sub Type Information GO to Pinpoint Test BQ
U023B:00 Lost Communication With Image Processing Module B: No Sub Type Information GO to Pinpoint Test CK
U0300:51 Internal Control Module Software Incompatibility: Not Programmed GO to Pinpoint Test Z
U0401:00 Invalid Data Received from ECM/PCM A: No Sub Type Information GO to Pinpoint Test AI
U0401:64 Invalid Data Received from ECM/PCM A: Signal Plausibility Failure GO to Pinpoint Test AI
U0401:7C Invalid Data Received from ECM/PCM A: Slow Response GO to Pinpoint Test AI
U0401:86 Invalid Data Received from ECM/PCM A: Signal Invalid GO to Pinpoint Test AI
U0404:00 Invalid Data Received from Gear Shift Control Module A: No Sub Type Information GO to Pinpoint Test AV
U0420:00 Invalid Data Received from Power Steering Control Module "A": No Sub Type Information GO to Pinpoint Test AE
U0422:00 Invalid Data Received From Body Control Module: No Sub Type Information GO to Pinpoint Test D
U0423:00 Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information GO to Pinpoint Test AR
U0424:00 Invalid Data Received From HVAC Control Module: No Sub Type Information GO to Pinpoint Test CE
U0452:00 Invalid Data Received From Restraints Control Module: No Sub Type Information GO to Pinpoint Test BH
U0452:86 Invalid Data Received From Restraints Control Module: Signal Invalid GO to Pinpoint Test BH
U053B:00 Invalid Data Received From Image Processing Module A: No Sub Type Information GO to Pinpoint Test BQ
U2001:00 Reduced System Function: No Sub Type Information GO to Pinpoint Test AH
U2017:57 Control Module Software #2: Invalid/Incompatible Software Component GO to Pinpoint Test Z
U2017:93 Control Module Software #2: No Operation GO to Pinpoint Test Z
U2018:57 Control Module Software #3: Invalid/Incompatible Software Component GO to Pinpoint Test Z
U2024:51 Control Module Cal-Config Data: Not Programmed GO to Pinpoint Test Z
U2100:00 Initial Configuration Not Complete: No Sub Type Information GO to Pinpoint Test Z
U2101:00 Control Module Configuration Incompatible: No Sub Type Information GO to Pinpoint Test Z
U2107:00 Collision Mitigation By Braking: No Sub Type Information GO to Pinpoint Test R
U2107:68 Collision Mitigation By Braking: Event Information GO to Pinpoint Test AQ
U2108:68 Adaptive Cruise Control: Event Information GO to Pinpoint Test AQ
U2200:00 Control Module Configuration Memory Corrupt: No Sub Type Information GO to Pinpoint Test Z
U3000:00 Control Module: No Sub Type Information GO to Pinpoint Test Y
U3000:49 Control Module: Internal Electronic Failure GO to Pinpoint Test Y
U3000:4B Control Module: Over Temperature GO to Pinpoint Test Y
U3000:96 Control Module: Component Internal Failure GO to Pinpoint Test Y
U3002:62 Vehicle Identification Number: Signal Compare Failure GO to Pinpoint Test AF
U3003:16 Battery Voltage: Circuit Voltage Below Threshold GO to Pinpoint Test A
U3003:17 Battery Voltage: Circuit Voltage Above Threshold GO to Pinpoint Test F
U300A:29 Ignition Switch: Signal Invalid GO to Pinpoint Test A
U3012:68 Control Module Improper Wake-up Performance: Event Information GO to Pinpoint Test X
P050F:00 Brake Assist Vacuum Too Low: No Sub Type Information GO to Pinpoint Test CB
P0555:00 Brake Booster Pressure Sensor Circuit: No Sub Type Information GO to Pinpoint Test CO
P0556:00 Brake Booster Pressure Sensor Circuit Range/Performance: No Sub Type Information GO to Pinpoint Test CO
P0557:00 Brake Booster Pressure Sensor Circuit Low: No Sub Type Information GO to Pinpoint Test CO
P0558:00 Brake Booster Pressure Sensor Circuit High: No Sub Type Information GO to Pinpoint Test CO
P0559:00 Brake Booster Pressure Sensor Circuit Intermittent: No Sub Type Information GO to Pinpoint Test CO
P05FF:00 Brake Pressure Sensor / Brake Pedal Position Sensor Correlation: No Sub Type Information GO to Pinpoint Test CO
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.