2021 Ford Explorer TimberlineFACTORY OEM SERVICE PROCEDURE

Section 13 (Engine - 3.0L ECOBOOST): Installation: Engine

WARNING: This page is about a different variant/trim than selected.

For information on Ford Color Coded Illustrations refer to OEM Color Coding .

Special Tool(s) / General Equipment 

GFD511410Courtesy of FORD MOTOR COMPANY
303-1246 Engine Spreader Bar TKIT-2006UF-FLM TKIT-2006UF-ROW
GFD511411Courtesy of FORD MOTOR COMPANY
303-1634 Lift Eyes (2) TKIT-2014D-ROW3 TKIT-2014D-FL_ROW
Adjustable Mounting Arm
Wooden Block

Materials 

Name Specification
Motorcraft® Premium Long-Life Grease XG-1-E1 ESA-M1C75-B
NOTE: The turbocharger compressor vanes can be damaged by even the smallest particles. When removing any turbocharger or engine air intake system component, ensure that no debris enters the system. Failure to do so may result in damage to the turbocharger.
  1. Inspect the turbocharger or engine air intake system components and clean, if necessary.
  2. With the aid of an assistant and using the floor crane and chain, install the engine on the subframe.
    GFD511640Courtesy of FORD MOTOR COMPANY
  3. Install and adjust and tighten the adjustable mounting arm bolts. Use the General Equipment: Adjustable Mounting Arm
    GFD511436Courtesy of FORD MOTOR COMPANY
  4. Remove the floor crane and chain.
    GFD511452Courtesy of FORD MOTOR COMPANY
  5. Remove the spreader bar and quick links. Remove Special Service Tool: 303-1246 Engine Spreader Bar.
    GFD511451Courtesy of FORD MOTOR COMPANY
  6. Remove Special Service Tool: 303-1634 Lift Eyes (2).
    GFD511450Courtesy of FORD MOTOR COMPANY
  7. Remove Special Service Tool: 303-1634 Lift Eyes (2).
    GFD511449Courtesy of FORD MOTOR COMPANY
    • If removed, install new TC mounting studs.

      Torque: 102 lb.in (11.5 Nm)

    • Install a new TC gasket.

    GFD511641Courtesy of FORD MOTOR COMPANY
    1. Install new TC oil supply tube O-ring seals and a new TC oil supply tube oil filter. Lubricate the new TC oil supply tube O-ring seals with clean engine oil.
    2. Install a new TC coolant supply tube O-ring seal. Lubricate the new TC coolant supply tube O-ring seal with clean engine coolant.
    GFD511642Courtesy of FORD MOTOR COMPANY
    1. NOTE: Install the coolant supply tube and the oil supply tube to the engine block while installing the TC.

      Install the TC and loosely install the new fasteners.

    2. Tighten the fasteners in sequence.

      Torque: Fastener 1: 44 lb.ft (60 Nm) - Fastener 2: 44 lb.ft (60 Nm) - Fastener 3: 27 lb.ft (37 Nm) - Re-tighten fastener 1: 44 lb.ft (60 Nm) - Re-tighten fastener 2: 44 lb.ft (60 Nm) - Re-tighten fastener 3: 27 lb.ft (37 Nm)

    GFD511643Courtesy of FORD MOTOR COMPANY
    • Install the TC oil supply tube bolt.

      Torque: 18 lb.ft (24 Nm)

    • Connect the vacuum hose and clamp.

    GFD511444Courtesy of FORD MOTOR COMPANY
    • Install the TC coolant supply tube bolt.

      Torque: 89 lb.in (10 Nm)

    • Connect the TC coolant return hose and clamp.

    GFD511443Courtesy of FORD MOTOR COMPANY
  8. Install the heat shield and the bolts.

    Torque: 89 lb.in (10 Nm)

    GFD511187Courtesy of FORD MOTOR COMPANY
  9. Install a new TC oil return tube O-ring seal and lubricate with clean engine oil.
    GFD511644Courtesy of FORD MOTOR COMPANY
  10. Install a new TC oil return tube-to-engine block gasket.
    GFD511645Courtesy of FORD MOTOR COMPANY
  11. Install the TC oil return tube and the fasteners.

    Torque: 89 lb.in (10 Nm)

    GFD511439Courtesy of FORD MOTOR COMPANY
  12. NOTE: Make sure that a new component is installed.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.