WARNING: This page is about a different car, the 2020 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

The chart describes specific module configuration information:

Module Name	Module Address	Programmable Module Installation (PMI) Available	Reprogram/Flash Capable	Requires Adaptive Learning or Calibration	Available Progammable Parameters
APIM	7D0	Yes	Yes	No	Travel Link (touchscreen with navigation)
ATCM (Raptor)	792	No	No	No	None
ABS module	760	Yes	Yes	IVD initialization	None
ACM	727	Yes	Yes	No	Auxiliary 1 Engine noise enhancement enable/disable
BECMB	723	Yes	Yes	No	None
BCM	726	Yes	Yes	Ambient lighting calibration Rear view camera calibration	Approach detection Autolamp delay Auto lock/unlock Auto relock Bed lamp enable/disable Body manufacture code configuration DRL configuration DRL by autolamps configuration Global open/global close Keypad enable Lock feedback light Mislock horn One/two stage unlock Park lock control Perimeter alarm Piezo Sounder feedback Police dark car feature Power lock enable Power point max time/time out Rain sensing enable Rear fold mirror Remote start enable/disable Trim lock/unlock configuration Valet mode
CCM	764	Yes	Yes	Radar horizontal and vertical alignment calibration	None
DSP	783	Yes	Yes	No	None
DACMC (integrated with ACM)	7D5	Yes	Yes	No	None
DC/ DC control module (voltage control module [VQM])	746	Yes	Yes	No	None
DDM	740	Yes	Yes	Windows initialization	None
DSM	744	Yes	Yes	No	None
SCMG	712	Yes	Yes	No	None
SCME (integrated with DSM)	776	Yes	Yes	No	None
FCDIM (4.2-inch screen)	7A5	Yes (vehicles NOT equipped with SYNC)	Yes (vehicles NOT equipped with SYNC)	No	None
FCIM	7A7	Yes	Yes	No	None
GWM	716	Yes	Yes	No	None
HUD module	7B2	No	No	No	None
HSWM	714	Yes	Yes	No	Temperature setpoint Low Medium High
IPC	720	Yes	Yes	No	Automatic regeneration control (diesel only) Manual regeneration control (diesel only) Remote start feature configuration Climate settings driver seatpassenger seatsteering wheel Trailer brake gain warning Trailer brake controller
IPMA module	706	Yes	Yes	Camera calibration	None
IPMB	7B1	Yes	Yes	Camera calibration LIN new model initialization	None
OCSM	765	No	No	OCSM re-zero	None
PAM (integrated with BCM)	736	Yes	Yes	No	None
SCMH	713	Yes	Yes	No	None
PSCM	730	Yes	Yes	No	None
PCM	7E0	Yes	Yes	Misfire Monitor Neutral Profile Correction procedure (except Diesel) PATS parameter reset	None
PDM	741	Yes	Yes	Windows initialization	None
PRB	766	No	No	No	None
RTM	751	Yes	Yes	No	None
RCM	737	Yes	Yes	No	Driver Beltminder status Passenger Beltminder status
SODL	7C4	Yes	Yes	No	BLIS/ CTA enable/disable
SODR	7C6	Yes	Yes	No	BLIS/ CTA enable/disable
SCCM	724	Yes	Yes	No	None
TCU	754	Yes	No	No	None
TBM	757	No	No	No	None
TRM	791	Yes	Yes	No	None
TCCM	761	Yes	No	No	None
TCM (10R80 transmission)	7E1	Yes	Yes	Transmission Strategy Download	None
VDM	721	Yes	Yes	Suspension height sensor calibration	None

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.

• Brakes feel soft, pull hard to one side, or make grinding noises.

• The engine overheats, stalls repeatedly, or misfires under load.

• You are missing required tools, torque specs, or safe lifting equipment.

• You are not confident in the next step or safety outcome.

Safety Warning

Module Configuration and Parameter Chart

Use the Manual With the Right Hardware

When to See a Mechanic

Rather have a pro handle this?