Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Ford Escape SE Plug-In HybridFACTORY OEM SERVICE PROCEDURE
Electric Powertrain Control System DTCS
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| U0293:00 | Lost Communication with Hybrid/EV Powertrain Control Module: No Sub Type Information | GO to Pinpoint Test BV |
| C0030:00 | Left Front Tone Wheel: No Sub Type Information | GO to Pinpoint Test BP |
| C0033:00 | Right Front Tone Wheel: No Sub Type Information | GO to Pinpoint Test BP |
| C0036:00 | Left Rear Tone Wheel: No Sub Type Information | GO to Pinpoint Test BP |
| C0039:00 | Right Rear Tone Wheel: No Sub Type Information | GO to Pinpoint Test BP |
| C0049:00 | Brake Fluid Level: No Sub Type Information | GO to Pinpoint Test BP |
| C004B:00 | Brake Fluid Level Sensor/Switch "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BP |
| C004C:00 | Brake Booster Motor "A" Position Sensor Exceeded Learning Limit: No Sub Type Information | GO to Pinpoint Test BP |
| C004E:00 | Brake System Pressure Control Valve Actuator Stuck: No Sub Type Information | GO to Pinpoint Test BP |
| C004F:00 | ABS Control Module Over Temperature: No Sub Type Information | GO to Pinpoint Test BP |
| C0061:00 | Lateral Acceleration Sensor: No Sub Type Information | GO to Pinpoint Test BP |
| C0062:00 | Longitudinal Acceleration Sensor: No Sub Type Information | GO to Pinpoint Test BP |
| C0500:00 | Left Front Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BP |
| C0501:00 | Left Front Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C0504:00 | Left Front Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BP |
| C0506:00 | Right Front Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BP |
| C0507:00 | Right Front Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C050A:00 | Right Front Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BP |
| C050C:00 | Left Rear Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BP |
| C050D:00 | Left Rear Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C0510:00 | Left Rear Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BP |
| C0512:00 | Right Rear Wheel Speed Sensor "A" Circuit/Open: No Sub Type Information | GO to Pinpoint Test BP |
| C0513:00 | Right Rear Wheel Speed Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C0516:00 | Right Rear Wheel Speed Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BP |
| C0518:00 | Left Front Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BP |
| C0519:00 | Right Front Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BP |
| C051A:00 | Left Rear Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BP |
| C051B:00 | Right Rear Wheel Speed Sensor - Mechanical: No Sub Type Information | GO to Pinpoint Test BP |
| C052B:00 | ABS Pump Motor Control Range/Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C052D:00 | ABS Pump Motor Control Circuit High: No Sub Type Information | GO to Pinpoint Test BP |
| C052E:00 | ABS Pump Motor Control Circuit Low: No Sub Type Information | GO to Pinpoint Test BP |
| C053D:00 | Brake Pressure Sensor "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C0555:00 | Left Front Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BP |
| C0556:00 | Right Front Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BP |
| C0557:00 | Left Rear Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BP |
| C0558:00 | Right Rear Wheel Speed Sensor "A" Incorrect Component Installed: No Sub Type Information | GO to Pinpoint Test BP |
| C055C:00 | ABS Pump Motor Supply Voltage Circuit "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C055E:00 | Brake Hydraulic Circuit "A" Leak: No Sub Type Information | GO to Pinpoint Test BP |
| C0560:00 | Brake Pressure Sensor "A" Missing Calibration: No Sub Type Information | GO to Pinpoint Test BP |
| C0563:00 | ABS Control Module Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C0564:00 | ABS Control Module System Voltage Low: No Sub Type Information | GO to Pinpoint Test BP |
| C0565:00 | ABS Control Module System Voltage High: No Sub Type Information | GO to Pinpoint Test BP |
| C056A:00 | Brake Booster Pressure Sensor Power Supply Circuit: No Sub Type Information | GO to Pinpoint Test BP |
| C056B:00 | Brake Pressure Sensor "A" Intermittent/Erratic: No Sub Type Information | GO to Pinpoint Test BP |
| C0594:00 | Brake Booster Motor "A" Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C0596:00 | Brake Booster Motor "A" Current Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C0597:00 | Brake System Control Module "A" Performance: No Sub Type Information | GO to Pinpoint Test BP |
| C1013:00 | Brake System Pressure: No Sub Type Information | GO to Pinpoint Test BP |
| C101F:00 | Generic Valve Failure: No Sub Type Information | GO to Pinpoint Test BP |
| C113A:62 | Wake-up Control: Signal Compare Failure | GO to Pinpoint Test A |
| P0560:00 | System Voltage: No Sub Type Information | GO to Pinpoint Test BR |
| P0562:00 | System Voltage Low: No Sub Type Information | GO to Pinpoint Test BS |
| P0563:00 | System Voltage High: No Sub Type Information | GO to Pinpoint Test C |
| P0600:49 | Serial Communication Link: Internal Electronic Failure | GO to Pinpoint Test D |
| P0600:88 | Serial Communication Link: Bus Off | GO to Pinpoint Test D |
| P060A:44 | Internal Control Module Monitoring Processor Performance: Data Memory Failure | GO to Pinpoint Test E |
| P060A:47 | Internal Control Module Monitoring Processor Performance: Watchdog/Safety ΞΌC Failure | GO to Pinpoint Test E |
| P060A:86 | Internal Control Module Monitoring Processor Performance: Signal Invalid | GO to Pinpoint Test D |
| P060A:88 | Internal Control Module Monitoring Processor Performance: Bus Off | GO to Pinpoint Test D |
| P060B:47 | Internal Control Module A/D Processing Performance: Watchdog/Safety ΞΌC Failure | GO to Pinpoint Test F |
| P060B:62 | Internal Control Module A/D Processing Performance: Signal Compare Failure | GO to Pinpoint Test F |
| P060C:41 | Internal Control Module Main Processor Performance: General Checksum Failure | GO to Pinpoint Test G |
| P060C:42 | Internal Control Module Main Processor Performance: General Memory Failure | GO to Pinpoint Test G |
| P060C:44 | Internal Control Module Main Processor Performance: Data Memory Failure | GO to Pinpoint Test G |
| P060C:47 | Internal Control Module Main Processor Performance: Watchdog/Safety ΞΌC Failure | GO to Pinpoint Test G |
| P0613:86 | TCM Processor: Signal Invalid | GO to Pinpoint Test H |
| P0613:92 | TCM Processor: Performance Or Incorrect Operation | GO to Pinpoint Test H |
| P061A:92 | Internal Control Module Torque Performance: Performance or Incorrect Operation | GO to Pinpoint Test BT |
| P061A:93 | Internal Control Module Torque Performance: No Operation | GO to Pinpoint Test BT |
| P061B:64 | Internal Control Module Torque Calculation Performance: No Operation | GO to Pinpoint Test BT |
| P064F:00 | Unauthorized Software/Calibration Detected: No Sub Type Information | GO to Pinpoint Test I |
| P06A6:00 | Sensor Reference Voltage "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| P06A7:00 | Sensor Reference Voltage "B" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| P06A8:00 | Sensor Reference Voltage "C" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| P06A9:00 | Sensor Reference Voltage "D" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| P06B1:00 | Sensor Power Supply "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test B |
| P06B8:00 | Internal Control Module Non-Volatile Random Access Memory (NVRAM) Error: No Sub Type Information | GO to Pinpoint Test J |
| P071A:1F | Transmission Mode Switch "A" Circuit: Circuit Intermittent | GO to Pinpoint Test BW |
| P071B:00 | Transmission Mode Switch "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test BW |
| P071C:00 | Transmission Mode Switch "A" Circuit High: No Sub Type Information | GO to Pinpoint Test BW |
| P0726:62 | Engine Speed Input Circuit Range/Performance: Signal Compare Failure | GO to Pinpoint Test BX |
| P0811:00 | Excessive Clutch "A" Slippage: No Sub Type Information | GO to Pinpoint Test CU |
| P0886:00 | TCM Power Relay Control Circuit Low: No Sub Type Information | GO to Pinpoint Test K |
| P0887:00 | TCM Power Relay Control Circuit High: No Sub Type Information | GO to Pinpoint Test K |
| P088E:00 | Planetary Gear Set Failure: No Sub Type Information | GO to Pinpoint Test BY |
| P0A0A:13 | High Voltage System Interlock Circuit "A": Circuit Open | GO to Pinpoint Test BU |
| P0A11:00 | DC/DC Converter Enable Circuit/Open: No Sub Type Information | GO to Pinpoint Test CN |
| P0A18:00 | Motor Torque Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| P0A1A:06 | Generator Control Module: Algorithm Based Failures | GO to Pinpoint Test L |
| P0A1B:06 | Drive Motor "A" Control Module Performance: Algorithm Based Failures | GO to Pinpoint Test BT |
| P0A1D:08 | Hybrid/EV Powertrain Control Module "A": Bus Signal/Message Failures | GO to Pinpoint Test M |
| P0A23:00 | Generator Torque Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test B |
| P0A2B:64 | Drive Motor "A" Temperature Sensor "A" Circuit Range/Performance: Signal Plausibility Failure | GO to Pinpoint Test BZ |
| P0A2C:00 | Drive Motor "A" Temperature Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test BZ |
| P0A2D:00 | Drive Motor "A" Temperature Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test BZ |
| P0A2F:94 | Drive Motor "A" Over Temperature: Unexpected Operation | GO to Pinpoint Test N |
| P0A37:64 | Generator Temperature Sensor Circuit Range/Performance: Signal Plausibility Failure | GO to Pinpoint Test O |
| P0A38:00 | Generator Temperature Sensor Circuit Low: No Sub Type Information | GO to Pinpoint Test O |
| P0A39:00 | Generator Temperature Sensor Circuit High: No Sub Type Information | GO to Pinpoint Test O |
| P0A3C:94 | Drive Motor "A" Inverter Over Temperature: Unexpected Operation | GO to Pinpoint Test P |
| P0A3F:00 | Drive Motor "A" Position Sensor Circuit: No Sub Type Information | GO to Pinpoint Test CA |
| P0A40:00 | Drive Motor "A" Position Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test R |
| P0A44:92 | Drive Motor "A" Position Sensor Circuit Overspeed: Performance Or Incorrect Operation | GO to Pinpoint Test CB |
| P0A45:00 | Drive Motor "B" Position Sensor Circuit: No Sub Type Information | GO to Pinpoint Test Q |
| P0A4C:00 | Generator Position Sensor Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test R |
| P0A50:92 | Generator Position Sensor Circuit Overspeed: Performance Or Incorrect Operation | GO to Pinpoint Test S |
| P0A5D:00 | Drive Motor "A" Phase U Current: No Sub Type Information | GO to Pinpoint Test CC |
| P0A5F:00 | Drive Motor "A" Phase U Current High: No Sub Type Information | GO to Pinpoint Test CD |
| P0A60:00 | Drive Motor "A" Phase V Current: No Sub Type Information | GO to Pinpoint Test CC |
| P0A62:00 | Drive Motor "A" Phase V Current High: No Sub Type Information | GO to Pinpoint Test CD |
| P0A63:00 | Drive Motor "A" Phase W Current: No Sub Type Information | GO to Pinpoint Test CC |
| P0A65:00 | Drive Motor "A" Phase W Current High: No Sub Type Information | GO to Pinpoint Test CD |
| P0A6F:00 | Generator Phase U Current: No Sub Type Information | GO to Pinpoint Test CC |
| P0A71:00 | Generator Phase U Current High: No Sub Type Information | GO to Pinpoint Test T |
| P0A72:00 | Generator Phase V Current: No Sub Type Information | GO to Pinpoint Test CC |
| P0A74:00 | Generator Phase V Current High: No Sub Type Information | GO to Pinpoint Test T |
| P0A75:00 | Generator Phase W Current: No Sub Type Information | GO to Pinpoint Test CC |
| P0A77:00 | Generator Phase W Current High: No Sub Type Information | GO to Pinpoint Test T |
| P0A78:96 | Drive Motor "A" Inverter Performance: Component Internal Failure | GO to Pinpoint Test U |
| P0A7A:96 | Generator Inverter Performance: Component Internal Failure | GO to Pinpoint Test U |
| P0A7D:00 | Hybrid/EV Battery Pack State of Charge Low: No Sub Type Information | GO to Pinpoint Test CE |
| P0A94:00 | DC/DC Converter "A" Performance: No Sub Type Information | GO to Pinpoint Test CF |
| P0AEE:00 | Drive Motor Inverter Temperature Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test W |
| P0AEF:00 | Drive Motor Inverter Temperature Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test W |
| P0BCD:00 | Generator Inverter Temperature Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test V |
| P0BCE:00 | Generator Inverter Temperature Sensor "A" Circuit Low: No Sub Type Information | GO to Pinpoint Test W |
| P0BFD:00 | Drive Motor "A" Phase U-V-W Current Sensor Correlation: No Sub Type Information | GO to Pinpoint Test AH |
| P0C00:00 | Drive Motor "A" Current Low: No Sub Type Information | GO to Pinpoint Test CG |
| P0C03:00 | Drive Motor "B" Current Low: No Sub Type Information | GO to Pinpoint Test X |
| P0C17:00 | Drive Motor "A" Position Sensor Not Learned: No Sub Type Information | GO to Pinpoint Test AI |
| P0C19:00 | Drive Motor "A" Torque Delivered Performance: No Sub Type Information | GO to Pinpoint Test CH |
| P0C2F:71 | Internal Control Module Drive Motor/Generator-Engine Speed Sensor Performance: Actuator Stuck | GO to Pinpoint Test BY |
| P0C2F:92 | Internal Control Module Drive Motor/Generator-Engine Speed Sensor Performance: Performance Or Incorrect Operation | GO to Pinpoint Test Y |
| P0C2F:93 | Internal Control Module Drive Motor/Generator-Engine Speed Sensor Performance: No Operation | GO to Pinpoint Test Y |
| P0C39:00 | DC/DC Converter Temperature Sensor "A" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test W |
| P0C3B:00 | DC/DC Converter Temperature Sensor "A" Circuit High: No Sub Type Information | GO to Pinpoint Test W |
| P0C3E:00 | DC/DC Converter Temperature Sensor "B" Circuit Range/Performance: No Sub Type Information | GO to Pinpoint Test W |
| P0C40:00 | DC/DC Converter Temperature Sensor "B" Circuit High: No Sub Type Information | GO to Pinpoint Test W |
| P0C50:00 | Drive Motor "A" Position Sensor Circuit "A": No Sub Type Information | GO to Pinpoint Test CA |
| P0C51:00 | Drive Motor "A" Position Sensor Circuit "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test Z |
| P0C52:00 | Drive Motor "A" Position Sensor Circuit "A" Low: No Sub Type Information | GO to Pinpoint Test CI |
| P0C53:00 | Drive Motor "A" Position Sensor Circuit "A" High: No Sub Type Information | GO to Pinpoint Test CJ |
| P0C55:00 | Drive Motor "A" Position Sensor Circuit "B": No Sub Type Information | GO to Pinpoint Test CK |
| P0C57:00 | Drive Motor "A" Position Sensor Circuit "B" Low: No Sub Type Information | GO to Pinpoint Test CL |
| P0C58:00 | Drive Motor "A" Position Sensor Circuit "B" High: No Sub Type Information | GO to Pinpoint Test CM |
| P0C5F:00 | Drive Motor "B" Position Sensor Circuit "B": No Sub Type Information | GO to Pinpoint Test AA |
| P0C64:00 | Generator Position Sensor Circuit A: No Sub Type Information | GO to Pinpoint Test Q |
| P0C65:00 | Generator Position Sensor Circuit "A" Range/Performance: No Sub Type Information | GO to Pinpoint Test Z |
| P0C66:00 | Generator Position Sensor Circuit "A" Low: No Sub Type Information | GO to Pinpoint Test AB |
| P0C67:00 | Generator Position Sensor Circuit "A" High: No Sub Type Information | GO to Pinpoint Test AC |
| P0C6B:00 | Generator Position Sensor Circuit "B" Low: No Sub Type Information | GO to Pinpoint Test AD |
| P0C6C:00 | Generator Position Sensor Circuit "B" High: No Sub Type Information | GO to Pinpoint Test AE |
| P0C79:00 | Drive Motor "A" Inverter Voltage Too High: No Sub Type Information | GO to Pinpoint Test AF |
| P0CA3:00 | DC/DC Converter Step Up Voltage Performance: No Sub Type Information | GO to Pinpoint Test CN |
| P0D32:00 | DC/DC Converter Over Temperature: No Sub Type Information | GO to Pinpoint Test N |
| P0D33:00 | DC/DC Converter Current High: No Sub Type Information | GO to Pinpoint Test CO |
| P0DA8:00 | Hybrid/EV Battery Voltage/Drive Motor "A" Inverter Voltage Correlation: No Sub Type Information | GO to Pinpoint Test AG |
| P0DFA:00 | Generator Phase U-V-W Current Sensor Correlation: No Sub Type Information | GO to Pinpoint Test CV |
| P0DFC:00 | Generator Position Sensor Not Learned: No Sub Type Information | GO to Pinpoint Test AI |
| P0E4E:00 | Engine Failed to Crank: No Sub Type Information | GO to Pinpoint Test BY |
| P0E51:00 | DC/DC Converter Temperature Sensor "A" Circuit: No Sub Type Information | GO to Pinpoint Test B |
| P0E52:00 | DC/DC Converter Temperature Sensor "A" Circuit Range / Performance: No Sub Type Information | GO to Pinpoint Test CC |
| P0E57:00 | DC/DC Converter Input Voltage Too High: No Sub Type Information | GO to Pinpoint Test CP |
| P0E59:00 | DC/DC Converter Temperature Sensor "C" Circuit Range / Performance: No Sub Type Information | GO to Pinpoint Test CQ |
| P0E5A:00 | DC/DC Converter Temperature Sensor "C" Circuit Low: No Sub Type Information | GO to Pinpoint Test CR |
| P0E5B:00 | DC/DC Converter Temperature Sensor "C" Circuit High: No Sub Type Information | GO to Pinpoint Test CR |
| P0E71:00 | Generator Torque Delivered Performance: No Sub Type Information | GO to Pinpoint Test AJ |
| P0EE3:00 | A/C Refrigerant Distribution Valve "B" Control Circuit/Open: No Sub Type Information | GO to Pinpoint Test CZ |
| P0EE4:00 | A/C Refrigerant Distribution Valve "B" Control Circuit Low: No Sub Type Information | GO to Pinpoint Test CZ |
| P0EE5:00 | A/C Refrigerant Distribution Valve "B" Control Circuit High: No Sub Type Information | GO to Pinpoint Test CZ |
| P1635:00 | Tire/Axle Out of Acceptable Range: No Sub Type Information | GO to Pinpoint Test CS |
| P174E:00 | Output Shaft Speed / ABS Wheel Speed Correlation: No Sub Type Information | GO to Pinpoint Test CT |
| P1920:62 | Engine Speed Signal: Signal Compare Failure | GO to Pinpoint Test CU |
| P1A07:00 | Inverter High Voltage Performance: No Sub Type Information | GO to Pinpoint Test AK |
| P1A0A:02 | Immediate Shutdown Signal A: General Signal Failure | GO to Pinpoint Test AL |
| P1A0C:00 | Hybrid Powertrain Control Module - Engine Failure: No Sub Type Information | GO to Pinpoint Test CW |
| P1A0D:62 | Hybrid Powertrain Control Module - Generator Disabled: Signal Compare Failure | GO to Pinpoint Test CV |
| P1A0D:64 | Hybrid Powertrain Control Module - Generator Disabled: Signal Plausibility Failure | GO to Pinpoint Test CV |
| P1A0D:96 | Hybrid Powertrain Control Module - Generator Disabled: Component Internal Failure | GO to Pinpoint Test CV |
| P1A0E:62 | Hybrid Powertrain Control Module - Motor Disabled: Signal Compare Failure | GO to Pinpoint Test AH |
| P1A0E:64 | Hybrid Powertrain Control Module - Motor Disabled: Signal Plausibility Failure | GO to Pinpoint Test AH |
| P1A0E:96 | Hybrid Powertrain Control Module - Motor Disabled: Component Internal Failure | GO to Pinpoint Test AH |
| P1A0F:00 | Hybrid Powertrain Control Module - Vehicle Disabled: No Sub Type Information | GO to Pinpoint Test CW |
| P1A10:00 | Hybrid Powertrain Control Module - Battery Disabled: No Sub Type Information | GO to Pinpoint Test CX |
| P1A13:00 | Hybrid Powertrain Control Module - Regenerative Braking Disabled: No Sub Type Information | GO to Pinpoint Test CY |
| P1A40:00 | ABS Control Module Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test BP |
| P1A41:00 | ABS Control Module Programming Error: No Sub Type Information | GO to Pinpoint Test BP |
| P2531:00 | Ignition Switch Run Position Circuit Low: No Sub Type Information | GO to Pinpoint Test BQ |
| P2533:1F | Ignition Switch On/Start Position Circuit: Circuit Intermittent | GO to Pinpoint Test BQ |
| P2533:62 | Ignition Switch On/Start Position Circuit: Signal Compare Failure | GO to Pinpoint Test BQ |
| P2C94:00 | Hybrid/EV Battery Contactor Control Supply Circuit Low: No Sub Type Information | GO to Pinpoint Test DA |
| P2C95:00 | Hybrid/EV Battery Contactor Control Supply Circuit High: No Sub Type Information | GO to Pinpoint Test DA |
| U0100:00 | Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test AM |
| U0103:87 | Lost Communication With Gear Shift Control Module A: No Sub Type Information | GO to Pinpoint Test AN |
| U010F:00 | Lost Communication With Air Conditioning Control Module: No Sub Type Information | GO to Pinpoint Test AO |
| U0111:00 | Lost Communication With Battery Energy Control Module "A": No Sub Type Information | GO to Pinpoint Test AP |
| U0121:00 | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": No Sub Type Information | GO to Pinpoint Test AQ |
| U0121:8F | Lost Communication With Anti-Lock Brake System (ABS) Control Module "A": Erratic | GO to Pinpoint Test AQ |
| U0136:87 | Lost Communication With Rear Differential Control Module: Missing Message | GO to Pinpoint Test AR |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AS |
| U0143:00 | Lost Communication With Body Control Module "C": No Sub Type Information | GO to Pinpoint Test AT |
| U0151:00 | Lost Communication With Restraints Control Module: No Sub Type Information | GO to Pinpoint Test AU |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AV |
| U0159:87 | Lost Communication With Parking Assist Control Module "A": Missing Message | GO to Pinpoint Test AW |
| U0164:00 | Lost Communication With HVAC Control Module: No Sub Type Information | GO to Pinpoint Test AX |
| U016A:00 | Lost Communication With Global Positioning System Module: No Sub Type Information | GO to Pinpoint Test AY |
| U0198:00 | Lost Communication With Telematic Control Module: No Sub Type Information | GO to Pinpoint Test AZ |
| U019B:00 | Lost Communication with Battery Charger Control Module "A": No Sub Type Information | GO to Pinpoint Test BA |
| U0214:00 | Lost Communication With Remote Function Actuation Module: No Sub Type Information | GO to Pinpoint Test BB |
| U023A:00 | Lost Communication With Image Processing Module A: No Sub Type Information | GO to Pinpoint Test BC |
| U0253:87 | Lost Communication With Accessory Protocol Interface Module: Missing Message | GO to Pinpoint Test BD |
| U0298:00 | Lost Communication With DC/DC Converter Control Module "A": No Sub Type Information | GO to Pinpoint Test BE |
| U0315:00 | Software Incompatibility with Anti-Lock Brake System (ABS) Control Module: No Sub Type Information | GO to Pinpoint Test BP |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | GO to Pinpoint Test BF |
| U0412:00 | Invalid Data Received From Battery Energy Control Module "A": No Sub Type Information | GO to Pinpoint Test BF |
| U0418:00 | Invalid Data Received from Brake System Control Module "A": No Sub Type Information | GO to Pinpoint Test BF |
| U045A:56 | Invalid Data Received From Parking Assist Control Module "A": Invalid Incompatible Configuration | GO to Pinpoint Test BF |
| U049C:00 | Invalid Data Received From Battery Charger Control Module "A": No Sub Type Information | GO to Pinpoint Test BF |
| U0515:82 | Invalid Data Received From Remote Function Actuation Module: No Sub Type Information | GO to Pinpoint Test BF |
| U053B:00 | Invalid Data Received From Image Processing Module: Signal Invalid | GO to Pinpoint Test BF |
| U069E:81 | Lost Communication With Coolant Heater "A": Invalid Serial Data Received | GO to Pinpoint Test BG |
| U069E:87 | Lost Communication With Coolant Heater "A": Missing Message | GO to Pinpoint Test BG |
| U1011:86 | Invalid Internal Control Module Monitoring Data Received from ECM/PCM: Signal Invalid | GO to Pinpoint Test BH |
| U1012:86 | Invalid Internal Control Module Monitoring Data Received from Anti-Lock Brake System (ABS) Control Module: Signal Invalid | GO to Pinpoint Test BI |
| U101E:86 | Invalid Internal Control Module Monitoring Data Received from Gear Shift Module: Signal Invalid | GO to Pinpoint Test BJ |
| U1027:00 | ABS Control Module Lost Communication With ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BP |
| U1028:00 | ABS Control Module Received Invalid Data from ECM/PCM "A": No Sub Type Information | GO to Pinpoint Test BP |
| U103B:00 | Invalid Internal Control Module Monitoring Data Received from Differential Control Module - Rear: No Sub Type Information | GO to Pinpoint Test BK |
| U2016:04 | Control Module Main Software: System Internal Failures | GO to Pinpoint Test BL |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test BL |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | GO to Pinpoint Test BL |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test BL |
| U301B:00 | Control Module Wake-up Circuit "A" Low: No Sub Type Information | GO to Pinpoint Test BM |
| U351B:00 | High Voltage System Interlock Circuit "D" Low: No Sub Type Information | GO to Pinpoint Test BN |
| U351F:00 | High Voltage System Interlock Circuit "E" Low: No Sub Type Information | GO to Pinpoint Test BO |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.