Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Ford Edge STFACTORY OEM SERVICE PROCEDURE
Cruise Control Module (CCM)
| DTC | Description | Action |
|---|---|---|
| B142E:78 | Forward Looking Sensor Horizontal Alignment: Alignment or Adjustment Incorrect | GO to Pinpoint Test E |
| B1432:78 | Forward Looking Sensor Vertical Alignment: Alignment or Adjustment Incorrect | This DTC can only be set at the assembly plant during the plant alignment process. If DTC B1432:78 sets, a reflash of the CCM and the vertical and horizontal aim procedure must be performed. REFER to: Cruise Control Radar Alignment |
| B1433:54 | Forward Looking Sensor Alignment: Missing Calibration | GO to Pinpoint Test E |
| C1001:08 | Vision System Camera: Bus Signal/Message Failure | GO to Pinpoint Test F |
| C1A67:96 | Forward Looking Sensor: Component Internal Failure | GO to Pinpoint Test G |
| C1A67:97 | Forward Looking Sensor: Component or System Operation Obstructed or Blocked | GO to Pinpoint Test H |
| C1A67:98 | Forward Looking Sensor: Component or System Over Temperature | The CCM was over-temperature. This may occur during extended use in extremely high weather temperatures. The adaptive cruise control system operation resumes after the CCM cools. |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test I |
| U2300:55 | Central Configuration: Not Configured | GO to Pinpoint Test I |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new CCM. REFER to: Cruise Control Module (CCM) |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). RETEST the adaptive cruise control system. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new CCM. REFER to: Cruise Control Module (CCM) |
| U3000:44 | Control Module: Data Memory Failure | INSTALL a new CCM. REFER to: Cruise Control Module (CCM) |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new CCM. REFER to: Cruise Control Module (CCM) |
| U3002:62 | Vehicle Identification Number: Signal Compare Failure | This DTC sets when the stored VIN in the CCM does not match the VIN defined in the BCM. This may indicate that the original CCM is not installed in the vehicle, and has not been configured correctly. CARRY OUT the PMI (when the original module is not available) for the module in question as directed by the diagnostic scan tool. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test J |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test K |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.