Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Ford Edge STFACTORY OEM SERVICE PROCEDURE
Body Closures
Diagnostics in this article assume a certain skill level and knowledge of Ford-specific diagnostic practices. REFER to: Diagnostic Methods .
| DTC | Description | Action |
|---|---|---|
| B1219:11 | Interior Boot/Trunk Release Switch: Circuit Short To Ground | GO to Pinpoint Test C |
| B12E8:11 | Liftgate/Tailgate Control/Release Switch: Circuit Short To Ground | GO to Pinpoint Test C |
| B1495:11 | Hands Free Liftgate/Decklid Input Sensor: Circuit Short To Ground | GO to Pinpoint Test J |
| B11C4:23 | Boot/trunk close button: Signal Stuck Low | GO to Pinpoint Test C |
| B12E8:23 | Liftgate/Tailgate Control/Release Switch: Signal Stuck Low | GO to Pinpoint Test C |
| B144C:23 | Tailgate/Liftgate/Boot/Trunk Outer Handle Switch: Signal Stuck Low | GO to Pinpoint Test C |
| B144D:29 | Tailgate/Liftgate/Boot/Trunk Position Sensor 1: Signal Invalid | GO to Pinpoint Test B |
| B144E:29 | Tailgate/Liftgate/Boot/Trunk Position Sensor 2: Signal Invalid | GO to Pinpoint Test B |
| B144F:11 | Tailgate/Liftgate/Boot/Trunk Driver Motor: Circuit Short To Ground | GO to Pinpoint Test B |
| B144F:12 | Tailgate/Liftgate/Boot/Trunk Driver Motor: Circuit Short To Battery | GO to Pinpoint Test B |
| B144F:13 | Tailgate/Liftgate/Boot/Trunk Driver Motor: Circuit Open | GO to Pinpoint Test B |
| B144F:79 | Tailgate/Liftgate/Boot/Trunk Driver Motor: Mechanical Linkage Failure | GO to Pinpoint Test B |
| B1451:29 | Tailgate/Liftgate/Boot/Trunk Latch Centering Position Switch: Signal Invalid | GO to Pinpoint Test D |
| B1452:11 | Tailgate/Liftgate/Boot/Trunk Latch Release Actuator: Circuit Short To Ground | GO to Pinpoint Test A |
| B1452:13 | Tailgate/Liftgate/Boot/Trunk Latch Release Actuator: Circuit Open | GO to Pinpoint Test A |
| B1453:29 | Tailgate/Liftgate/Boot/Trunk Latch Position Switch: Signal Invalid | GO to Pinpoint Test D |
| B1454:11 | Tailgate/Liftgate/Boot/Trunk Left Pinch Strip: Circuit Short To Ground | GO to Pinpoint Test G |
| B1454:13 | Tailgate/Liftgate/Boot/Trunk Left Pinch Strip: Circuit Open | GO to Pinpoint Test G |
| B1455:11 | Tailgate/Liftgate/Boot/Trunk Right Pinch Strip: Circuit Short To Ground | GO to Pinpoint Test G |
| B1455:13 | Tailgate/Liftgate/Boot/Trunk Right Pinch Strip: Circuit Open | GO to Pinpoint Test G |
| B145D:11 | Tailgate/Liftgate/Boot/Trunk Power Cinch Striker Motor: Circuit Short To Ground | GO to Pinpoint Test B |
| B145D:12 | Tailgate/Liftgate/Boot/Trunk Power Cinch Striker Motor: Circuit Short To Battery | GO to Pinpoint Test B |
| B145D:13 | Tailgate/Liftgate/Boot/Trunk Power Cinch Striker Motor: Circuit Open | GO to Pinpoint Test B |
| B1515:78 | Tailgate/Liftgate/Boot/Trunk: Alignment or Adjustment Incorrect | GO to Pinpoint Test D |
| C1B14:11 | Sensor Supply Voltage A: Circuit Short To Ground | GO to Pinpoint Test B |
| U0101:87 | Lost Communication with TCM: Missing Message | GO to Pinpoint Test K |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to Pinpoint Test L |
| U0294:87 | Lost Communication With Powertrain Control Monitor Module: Missing Message | GO to Pinpoint Test M |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test N |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test O |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.