Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Module Configuration and Parameter Chart
The chart describes specific module configuration information:
| Module Name | Module Address | Programmable Module Installation (PMI) Available | Reprogram/Flash Capable | Requires Adaptive Learning or Calibration | Available Programmable Parameters |
|---|---|---|---|---|---|
| APIM | 7D0 | Yes | Yes | No | None |
| ABS module | 760 | Yes | Yes | IVD initialization | None |
| ACM | 727 | Yes | Yes | No | None |
| BECMB | 723 | Yes | Yes | No | None |
| BCM | 726 | Yes | Yes | Ambient lighting calibration Rear view camera calibration |
Bed lamp enable/disable DRL by autolamps configuration Exterior lamp outage Hood ajar switch Lighting type Locking feedback light Perimeter alarm Piezo sounder feedback Remote start enable/disable Remote start light enable |
| BCMB (auxiliary lighting) | 7B7 | Yes | Yes | No | Exterior lamp outage Lighting type |
| CCM | 764 | Yes | Yes | Radar horizontal and vertical alignment calibration | None |
| DSP | 783 | Yes | Yes | No | None |
| DDM | 740 | Yes | Yes | Windows initialization | None |
| DSM | 744 | Yes | Yes | No | Easy entry/exit enable |
| FCDIM (4.2-inch screen) | 7A5 | Yes | Yes | No | None |
| FCIM | 7A7 | Yes | Yes | No | None |
| GWM | 716 | Yes | Yes | No | None |
| GFM (trailer TPMS) | 7A1 | No | No | No | None |
| GFM2 (upfitter switch) | 7D2 | No | No | No | None |
| GPSM (4.2-inch screen) | 701 | Yes | Yes | No | None |
| HUD module | 7B2 | No | No | No | None |
| HSWM | 714 | Yes | Yes | No | Temperature setpoint Normal or warm Warmer or hot |
| IPC | 720 | Yes | Yes | No | Remote start feature configuration Climate settings driver seatpassenger seatsteering wheel Trailer brake controller |
| IPMA module | 706 | Yes | Yes | Camera calibration | None |
| IPMB | 7B1 | Yes | Yes | Camera calibration | None |
| PAM (integrated with BCM) | 736 | Yes | Yes | No | Rear parking aid enable |
| PCM | 7E0 | Yes | Yes | Misfire Monitor Neutral Profile Correction procedure | None |
| PDM | 741 | Yes | Yes | Windows initialization | None |
| RTM | 751 | Yes | Yes | No | None |
| RCM | 737 | Yes | Yes | No | Driver Beltminder status Passenger Beltminder status |
| RBM | 766 | No | No | No | None |
| SCME | 776 | Yes | Yes | No | None |
| SCMG | 712 | Yes | Yes | No | None |
| SCMH | 713 | Yes | Yes | No | None |
| SODL | 7C4 | Yes | Yes | No | Blockage enabled BLIS/ CTA enable/disable |
| SODR | 7C6 | Yes | Yes | No | Blockage enabled BLIS/ CTA enable/disable |
| SASM | 797 | Yes | Yes | Steering Wheel Angle Trim Steering Motor Angle Trim |
None |
| SECM | 7C5 | Yes | Yes | Steering Wheel Angle Trim Steering Motor Angle Trim |
None |
| SCCM | 724 | Yes | Yes | No | None |
| TBM | 757 | No | No | No | None |
| TRM | 791 | Yes | Yes | No | None |
| TCM (6.7L diesel) | 7E9 | No | No | No | None |
| TCCM | 761 | No | No | No | None |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.