Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Ford Bronco Sport BaseFACTORY OEM SERVICE PROCEDURE
Body Control Module (BCM)
| DTC | Description | Action |
|---|---|---|
| B153F:01 | Power Distribution Box: General Electrical Failure | GO to Pinpoint Test A |
| B153F:08 | Power Distribution Box: Bus Signal/Message Failure | GO to Pinpoint Test A |
| B153F:49 | Power Distribution Box: Internal Electronic Failure | GO to Pinpoint Test A |
| B153F:9A | Power Distribution Box: Component or System Operating Conditions | GO to Pinpoint Test A |
| U0100:87 | Lost Communication With ECM/PCM "A": Missing Message | GO to Pinpoint Test B |
| U0121:87 | Lost Communication With Anti-Lock Brake System (ABS) Control Module: Missing Message | GO to Pinpoint Test C |
| U0131:87 | Lost Communication With Power Steering Control Module: Missing Message | GO to Pinpoint Test D |
| U0151:87 | Lost Communication With Restraints Control Module: Missing Message | GO to Pinpoint Test E |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to Pinpoint Test F |
| U0184:87 | Lost Communication With Radio: Missing Message | GO to Pinpoint Test G |
| U0198:87 | Lost Communication With Telematic Control Module: Missing Message | GO to Pinpoint Test H |
| U0199:87 | Lost Communication With "Door Control Module A": Missing Message | GO to Pinpoint Test I |
| U0200:87 | Lost Communication With "Door Control Module B": Missing Message | GO to Pinpoint Test J |
| U0212:87 | Lost Communication With Steering Column Control Module: Missing Message | GO to Pinpoint Test K |
| U023A:87 | Lost Communication With Image Processing Control Module A: Missing Message | GO to Pinpoint Test L |
| U0252:87 | Lost Communication With Lighting Control Module-Rear "B": Missing Message | GO to Pinpoint Test M |
| U0253:87 | Lost Communication With Accessory Protocol Interface Module: Missing Message | GO to Pinpoint Test N |
| U1000:00 | Solid State Driver Protection Active: Driver Disabled: No Sub Type Information | GO to Pinpoint Test O |
| U2005:85 | Vehicle Speed: Signal Above Allowable Range | GO to Pinpoint Test P |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | GO to Pinpoint Test Q |
| U2101:00 | Control Module Configuration Incomplete: No Sub Type Information | GO to Pinpoint Test Q |
| U2200:00 | Control Module Configuration Memory Corrupt: No Sub Type Information | GO to Pinpoint Test Q |
| U3000:49 | Control Module: Internal Electronic Failure | GO to Pinpoint Test R |
| U3006:16 | Control Module Input Power "A" Circuit/Open: Circuit Voltage Below Threshold | GO to Pinpoint Test S |
| U3006:17 | Control Module Input Power "A" Circuit/Open: Circuit Voltage Above Threshold | GO to Pinpoint Test U |
| U3006:1C | Control Module Input Power "A Circuit Open: Circuit Voltage Out of Range | GO to Pinpoint Test T |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
