Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Module Configuration and Parameter Chart
The chart describes specific module configuration information:
| Module Name | Module Address | Programmable Module Installation (PMI) Available | Reprogram/Flash Capable | Requires Adaptive Learning or Calibration | Available Programmable Parameters |
|---|---|---|---|---|---|
| ABS module | 760 | Yes | Yes | ABS calibration (with and without EBB) HCU solenoid calibration (without EBB) Brake System Pressure Bleeding (with and without EBB) PCMPATS key programming (with EBB) Module Initialization (Parameter Reset) (with EBB) |
None |
| ACM | 727 | Yes | Yes | No | None |
| APIM | 7D0 | Yes | Yes (diagnostic scan tool and USB flash drive) | APIM software update | None |
| ATCM | 792 | No | No | No | None |
| AWD module | 703 | Yes | Yes | No | None |
| BCM | 726 | Yes | Yes | PATS key programming (manual programming/not using the diagnostic scan tool) PATS parameter reset CEI If equipped with rear video parking aid, BCMLIN initialization TPMS sensor location calibration |
Lamp configuration |
| BCMC [ BJB] | 6F0 | Yes | Yes | No | None |
| CCM | 764 | Yes | Yes | CCM radar alignment | None |
| CHCM | 573 | Yes | Yes | No | None |
| DDM | 740 | Yes | Yes | Windows initialization | None |
| DSP | 783 | Yes | Yes | No | None |
| GWM | 716 | Yes | Yes (diagnostic scan tool and USB flash drive) | No | None |
| HVAC module | 733 | Yes | Yes | No | None |
| IPC | 720 | Yes | Yes (diagnostic scan tool and USB flash drive) | No | MyKey emergency text |
| IPMA | 706 | Yes | Yes | Camera alignment | None |
| IPMB | 7B1 | Yes | Yes | Camera alignment | None |
| OCS module | 765 | No | No | OCSM re-zero | None |
| PAM | 736 | Yes | Yes | No | None |
| PCM | 7E0 | Yes | Yes | PATS parameter reset Misfire Monitor Neutral Profile Correction |
None |
| PDM | 741 | Yes | Yes | Windows initialization | None |
| PSCM | 730 | Yes | Yes | No | None |
| RCM | 737 | Yes | Yes | ABS calibration service functions | None |
| RTM | 751 | Yes | Yes | No | None |
| SCCM | 724 | Yes | Yes | No | None |
| SIMA (Driveline Chassis Switch [DLCS]) | 770 | No | No | No | None |
| SODL | 7C4 | Yes | Yes | No | BLIS/ CTA enable/disable |
| SODR | 7C6 | Yes | Yes | No | BLIS/ CTA enable/disable |
| TCU | 754 | Yes | Yes (diagnostic scan tool and USB flash drive) | No | None |
| TRM | 791 | Yes | Yes | No | None |
| WACM | 725 | Yes | Yes | No | None |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
No obligation. See pricing before you book.