Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Test Procedure
- DM1 CHECK FOR DIAGNOSTIC TROUBLE CODES (DTCS)
Are DTCs P0106, P0107, P0108, or P0109 present?
Yes No GO to DM2. For symptoms without DTCs, GO to DM2.
For all others, RETURN to SYMPTOM CHARTS for further direction. - DM2 MONITOR THE MAP PID
Is the voltage between 0.5 - 4.95 V?
Yes No For DTC P0106. GO to DM9.
For all others, GO to DM8.GO to DM3. - DM3 CHECK THE VOLTAGE BETWEEN THE VREF AND SIGRTN CIRCUITS
- MAP Sensor connector disconnected.
- Ignition ON, engine OFF.
- Measure the voltage between:
(+) MAP Sensor Connector, Harness Side (-) MAP Sensor Connector, Harness Side VREF - Pin 2 SIGRTN - Pin 4
Is the voltage between 4.5 - 5.5 V?
Yes No GO to DM4. GO to PINPOINT TEST C . - DM4 CHECK FOR AN OPEN CIRCUIT
- PCM connector disconnected.
- Measure the resistance between:
(+) MAP Sensor Connector, Harness Side (-) PCM Connector, Harness Side MAP - Pin 1 MAP - Pin E18 SIGRTN - Pin 4 SIGRTN - Pin E6
Are the resistances less than 5 ohms?
Yes No GO to DM5. REPAIR the open circuit. Clear the PCM DTCs.
REPEAT the self-test. - DM5 CHECK FOR A SHORT TO GROUND
- Measure the resistance between:
(+) MAP Sensor Connector, Harness Side (-) MAP Sensor Connector, Harness Side MAP - Pin 1 SIGRTN - Pin 4 - Measure the resistance between:
(+) MAP Sensor Connector, Harness Side (-) MAP - Pin 1 Ground
Are the resistances greater than 10K ohms?
Yes No GO to DM6. REPAIR the short circuit. Clear the PCM DTCs.
REPEAT the self-test. - Measure the resistance between:
- DM6 CHECK FOR A SHORT TO VOLTAGE
- Ignition ON, engine OFF.
- Measure the voltage between:
(+) MAP Sensor Connector, Harness Side (-) MAP - Pin 1 Ground
Is any voltage present?
Yes No REPAIR the short circuit. Clear the PCM DTCs.
REPEAT the self-test.GO to DM7. - DM7 INDUCE THE OPPOSITE MAP VOLTAGE
- PCM connector connected.
- Connect a 5 amp fused jumper wire between the following:
Point A MAP Sensor Connector, Harness Side Point B MAP Sensor Connector, Harness Side MAP - Pin 1 SIGRTN - Pin 4 - Ignition ON, engine OFF.
- Access the PCM and monitor the MAP_V (VOLT) PID.
- Ignition ON, engine OFF.
Is the voltage less than 4.6 V?
Yes No INSTALL a new MAP sensor.
Refer to the Electronic Engine Controls article.
Clear the PCM DTCs. REPEAT the self-test.GO to DM10. - DM8 CHECK FOR AN INTERMITTENT CONCERN
- Ignition ON, engine OFF.
- Access the PCM and monitor the MAP_V (VOLT) PID.
- Carefully wiggle all accessible wiring and connectors associated with the circuit and look for a change in the PID state.
- Wiggle the harness connector to simulate road shock.
Does a sudden change in voltage occur while monitoring the PID?
Yes No REPAIR as necessary or INSTALL a new MAP sensor. Refer to the Electronic Engine Controls article.
Clear the PCM DTCs. REPEAT the self-test.Unable to duplicate or identify the concern at this time.
GO to PINPOINT TEST Z . - DM9 MAP RANGE OR PERFORMANCE NOTE: If MAP DTCs P0107 or P0108 are present, diagnose those DTCs first.
If any mass air flow (MAF) sensor related DTCs are present, diagnose those DTCs prior to diagnosing MAP DTC P0106.
- Ignition ON, engine OFF.
- Access the PCM and monitor the MAP_V (VOLT) PID.
- Record the KOEO MAP PID voltage.
- Ignition ON, engine running.
- Record the KOER MAP PID voltage.
Does the PID value change?
Yes No Unable to duplicate or identify the concern at this time.
GO to PINPOINT TEST Z .INSTALL a new MAP sensor.
REFER to the Electronic Engine Controls article.
Clear the PCM DTCs. REPEAT the self-test. - DM10 CHECK FOR CORRECT PCM OPERATION
- Disconnect all the PCM connectors.
- Visually inspect for:
- Connect all the PCM connectors and make sure they seat correctly.
- Carry out the PCM self-test.
- Verify the concern is still present.
Is the concern still present?
Yes No INSTALL a new PCM. REFER to FLASH ELECTRICALLY ERASABLE PROGRAMMABLE READ ONLY MEMORY (EEPROM) . The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
