Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2020 Ford EcoSport SESFACTORY OEM SERVICE PROCEDURE
External Pages
These are pages that do not belong to the exact selected vehicle (2020 Ford EcoSport S, 2.0L Eng VIN L), but are still accessible from a link in your vehicle's manual. Be very cautious using repair info from here because these pages may not apply to your vehicle.
- Different variant/trim
- Section 1 (Electronic Engine Controls - 1.0L ECOBOOST (92KW/125PS))
- Section 2 (Engine Cooling - 1.0L ECOBOOST (92KW/125PS))
- Section 3 (Accessory Drive - 1.0L ECOBOOST (92KW/125PS))
- Section 4 (Fuel System - General Information - 1.0L ECOBOOST (92KW/125PS))
- Section 5 (Starting System - 1.0L ECOBOOST (92KW/125PS))
- Section 6 (Fuel Tank And Fuel Lines - 1.0L ECOBOOST (92KW/125PS))
- Section 7 (Engine - 1.0L ECOBOOST (92KW/125PS))
- Section 8 (Automatic Transmission - 6-Speed Automatic Transmission - 6F15 (1 Of 2))
- Section 9 (Transmission Cooling - 6-Speed Automatic Transmission - 6F15)
- Section 10 (Fuel Charging And Controls - Turbocharger - 1.0L ECOBOOST (92KW/125PS))
- Section 11 (Automatic Transmission - 6-Speed Automatic Transmission - 6F15 (2 Of 2))
- Section 12 (Intake Air Distribution And Filtering - 1.0L ECOBOOST (92KW/125PS))
- Section 13 (Exhaust System - 1.0L ECOBOOST (92KW/125PS))
- Section 14 (Evaporative Emissions - 1.0L ECOBOOST (92KW/125PS))
- Section 15 (Fuel Charging And Controls - 1.0L ECOBOOST (92KW/125PS))
- Section 16 (Engine Ignition - 1.0L ECOBOOST (92KW/125PS))
- Section 17 (Rear Suspension - Fwd)
- Different car
- Section 1 (IPC Guided Routine Testing)
- Section 2 (Pcm Guided Routine Testing)
- Section 3 (APIM Guided Routine Testing)
- Section 4 (FDIM Guided Routine Testing)
- Section 5 (OEM Electrical Wiring Diagram Introduction)
- Section 6 (Engine Controls - Symptom Charts (Hybrid))
- Section 7 (Engine Controls - Pinpoint Tests (Hybrid))
- Section 8 (Engine Controls - Powertrain DTC Charts & Descriptions (Hybrid))
- Section 9 (Engine Controls - Diagnostic Methods (Hybrid))
- Section 10 (Engine Controls - Description & Operation (Hybrid))
- Section 11 (Engine Controls - Reference Values (Hybrid))
- Section 12 (Engine Controls - Introduction (Hybrid))
- Section 13 (EPAS Guided Routine)
- Section 14 (BCM Guided Routine)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.