2018 Ford Expedition MAX Platinum, 4WDFACTORY OEM SERVICE PROCEDURE

Module Configuration and Parameter Chart

The chart describes specific module configuration information:

Module Name Module Address Programmable Module Installation (PMI) Available Reprogram/Flash Capable Requires Adaptive Learning or Calibration Available Progammable Parameters
APIM 7D0 Yes No No Travel Link
ATCM 792 No No No None
ABS module 760 Yes Yes IVD initialization
Longitudinal acceleration sensor calibration
Park brake initialization		 None
ACM 727 Yes No No None
BECMB 723 Yes No No None
BCM 726 Yes Yes Key programming
PATS reset
Configuration Engine Immobilizer (CEI) configuration
Battery monitor sensor reset
LIN new module initialization
TPMS sensor location calibration		 Approach detection
Autolamp delay
Auto lock/unlock
Auto relock
Body manufacture code configuration
DRL configuration
Global open/global close
Keypad enable
Lock feedback light
Mislock horn
One/two stage unlock
Park lock control
Perimeter alarm
Piezo Sounder feedback
Power point max time/time out
Rain sensing enable
Rear fold seat
Remote start enable/disable
Trailer brake controller
Valet mode
CCM (Private CAN) 764 Yes No Radar horizontal and vertical alignment calibration None
Audio DSP 783 Yes No No None
DACMC (integrated with ACM) 7D5 Yes Yes No ANC function enable/disable
ESE function enable/disable
DCDC (Voltage Quality Module [VQM]) 714 Yes No No None
DCMR (electronic limited slip differential) 795 No No No None
DDM 740 Yes Yes No None
DSM 744 Yes No No None
FCIM 7A7 Yes Yes No None
GSM 732 No No No None
GWM 716 Yes No No None
HUD module 7B2 No No No None
HSWM 714 Yes No No None
IPC 720 Yes No No Remote start feature configuration
Remote start climate settings driver seat passenger seat rear defrost steering wheel
Trailer brake controller
IPMA module 706 Yes No Camera alignment None
IPMB 7B1 Yes No Camera alignment (360 deg. camera and Pro Trailer Backup Assist, if equipped)
LIN new model initialization		 None
OCS 765 No No OCSM re-zero None
PAM (integrated with BCM) 736 Yes Yes No None
PAM (Active park assist) 736 Yes Yes No None
PSCM 730 Yes Yes No None
PCM 7E0 Yes Yes Misfire Monitor Neutral Profile Correction procedure None
PDM 741 Yes Yes No None
RACM 774 Yes No No None
RBM 766 No No No None
RTM 751 Yes No No None
RCM 737 Yes No No None
RGTM 775 Yes Yes No None
RHVAC 785 No No No None
SCCM 724 Yes No No None
SCME (integrated with DSM) 776 Yes No No None
SCMG 712 Yes No No None
SCMH 713 Yes No No None
SCMJ 787 Yes No Third row seat learning None
SODL 7C4 Yes No No None
SODR 7C6 Yes No No None
TCU 754 Yes No No None
TBM 757 No No No None
TRM 791 Yes No No None
TCCM 761 No No No None
TCM 7E1 Yes Yes Transmission Strategy Download None
VDM 721 Yes Yes Height sensor calibration None
WACM 725 Yes No No None
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.