2018 Ford Escape Titanium, AWDFACTORY OEM SERVICE PROCEDURE

Module Configuration and Parameter Chart

WARNING: This page is about a different car, the 2017 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.

The charts describe specific module configuration information:

Module Name Module Address Programmable Module Installation (PMI) Available Reprogram/Flash Capable Requires Adaptive Learning or Calibration Available Progammable Parameters
ABS module 760 Yes Yes IVD initialization
Lateral sensor calibration
Longitudinal sensor calibration
Pressure sensor calibration
Central configuration data parameter learning
EPB apply and release routine		 None
APIM 7D0 Yes Yes No None
ACM 727 Yes Yes No None
BCM 726 Yes Yes No Remote start enable/disable
CCM 764 Yes Yes No None
DSP 783 Yes Yes No None
DDM 740 Yes Yes Window AUTO up/down functionality None
DSM 744 Yes Yes No None
FCIM 7A7 No Yes No None
FCDIM 7A5 Yes Yes No None
GPSM (if equipped) 701 Yes Yes No None
HCM 734 Yes Yes No None
HUD module 7B2 No No No None
HVAC module 733 Yes Yes No Remote start enable/disable
IPMA 706 Yes Yes No None
IPC 720 Yes Yes No Remote start enable/disable
Heated driver seat
System enable/disable
Climate heater menu
Quiet start
OCS 765 No No Seat weight sensor re-zero None
PAM 736 Yes Yes No None
PDM 741 Yes Yes Window AUTO up/down functionality None
PSCM 730 No No No None
PCM 7E0 Yes Yes No None
RGTM 775 Yes Yes No None
RFA module 731 Yes Yes No None
RCM 737 Yes Yes No None
SODL 7C4 Yes Yes No None
SODR 7C6 Yes Yes No None
SASM 797 No No No None
TCU module 754 Yes Yes No None
TRM 791 Yes Yes No None

Central Car Configuration - Body Control Module (BCM) and Instrument Panel Cluster (IPC) 

NOTE: The Body Control Module (BCM) and IPC have a unique procedure to set Car Configuration Parameters. Configuration changes made will affect both modules. On the scan tool, first select Module Programming > Programmable Parameters > Car Configuration Parameter(s) > Vehicle Configuration > Retrieve the Vehicle Configuration Data. Next select Module Programming > Programmable Parameters > Car Configuration Parameter(s) > Vehicle Configuration > Modify and Reinstate Vehicle Configuration Data. Change parameters as needed.
Module Name Module Address Programmable Module Installation (PMI) Available Reprogram/Flash Capable Requires Adaptive Learning or Calibration Available Car Configuration Parameters
BCM 726 Yes (through Car Configuration Parameters. Refer to Multifunction Electronic Modules . Yes No
NOTE: Do not change car configuration parameters except those listed below.
BLIS ® enable/disableLoud speaker quantities (6, 9 or 10)LanguagePark assist cameraPerimeter alarm enable/disableRemote start enable/disableTire sizeTowbarTrailer moduleTrailer stability assist
IPC 720 Yes Yes No
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.