2017 Ford Fusion Titanium, FWDFACTORY OEM SERVICE PROCEDURE

Module Configuration and Parameter Chart

WARNING: This page is about a different car, the 2016 Ford F-150. However, it is still accessible from the selected car via links, so may be relevant.

The chart describes specific module configuration information:

Module Name Module Address Programmable Module Installation (PMI) Available Reprogram/Flash Capable Requires Adaptive Learning or Calibration Available Progammable Parameters
APIM 7D0 Yes Yes No Travel Link (touchscreen with navigation)
ABS module 760 Yes Yes IVD initialization None
ACM 727 Yes Yes No Auxiliary 1
Engine noise enhancement enable/disable
BCM 726 Yes Yes Ambient lighting calibration
Rear view camera calibration		 Approach detection
Autolamp delay
Auto lock/unlock
Auto relock
Bed lamp enable/disable
Body manufacture code configuration
DRL by autolamps configuration
Keypad enable
Lock feedback light
Mislock horn
One/two stage unlock
Park lock control
Passive entry/lock/start
Perimeter alarm
Piezo Sounder feedback
Police dark car feature
Power lock enable
Power point max time/time out
Rain sensing enable
Rear fold mirror
Remote start enable/disable
Valet mode
CCM 764 Yes Yes Radar horizontal and vertical alignment calibration None
DSP 783 Yes Yes No None
DACMC (integrated with ACM) 7D5 Yes Yes No None
DC/ DC control module (voltage control module [VQM]) 746 Yes Yes No None
DDM 740 Yes Yes Windows initialization None
DSM 744 Yes Yes No None
SCMG 712 Yes Yes No None
EPB module 756 No No EPB apply and release None
SCME 776 Yes Yes No None
FCDIM (4.2-inch screen) 7A5 Yes Yes No None
FCIM 7A7 Yes Yes No None
GWM 716 Yes Yes No None
GPSM (without touchscreen) 701 Yes Yes No None
HUD module 7B2 No No No None
HSWM 714 Yes Yes No Temperature setpoint
Normal or warm
Warmer or hot
IPC 720 Yes Yes No Remote start feature configuration
Climate settings driver seat passenger seat steering wheel
Trailer brake gain warning
IPMA module 706 Yes Yes Camera calibration None
IPMB 7B1 Yes Yes Camera calibration
LIN new model initialization		 None
OCSM 765 No No OCSM re-zero None
PAM (integrated with BCM) 736 Yes Yes No None
SCMH 713 Yes Yes No None
PSCM 730 Yes Yes No None
PCM 7E0 Yes Yes Misfire Monitor Neutral Profile Correction procedure None
PDM 741 Yes Yes Windows initialization None
PRB 766 No No No None
RTM 751 Yes Yes No None
RCM 737 Yes Yes No Driver Beltminder status
Passenger Beltminder status
SODL 7C4 Yes Yes No Blockage enabled
BLIS/ CTA enable/disable
SODR 7C6 Yes Yes No Blockage enabled
BLIS/ CTA enable/disable
SCCM 724 Yes Yes No None
TBM 757 No No No None
TRM 791 Yes Yes No None
TCCM 761 No No No None
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.