Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2017 Ford Escape SFACTORY OEM SERVICE PROCEDURE
Information System And Entertainment System DTCS: Sync: FCDIM
| DTC | Description | Action |
|---|---|---|
| B10BD:11 | Multifunctional Switch: Circuit Short To Ground | GO to Pinpoint Test S |
| B10BD:13 | Multifunctional Switch: Circuit Open | GO to Pinpoint Test S |
| B10BD:23 | Multifunctional Switch: Signal Stuck Low | GO to Pinpoint Test S |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to: Parking Aid . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test Y |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test Z |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AA |
| U0264:00 | Lost Communication With Camera Module - Rear: No Sub Type Information | GO to Pinpoint Test X |
| U0423:68 | Invalid Data Received from Instrument Panel Cluster Control Module: Event Information | RETRIEVE and DIAGNOSE Diagnostic Trouble Codes (DTCs) present in the IPC. Refer to: Instrumentation, Message Center and Warning Chimes
. If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom. |
| U2013:87 | Switch Pack: Missing Message | GO to Pinpoint Test T |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the FCDIM. If there have been recent service actions with the FCDIM, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the FCDIM. If there have been recent service actions with the FCDIM, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the FCDIM. If there have been recent service actions with the FCDIM, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new FCDIM. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new FCDIM. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U3003:16 | Control Module Input Power "A": Circuit Voltage Below Threshold | GO to Pinpoint Test AC |
| U3003:17 | Control Module Input Power "A": Circuit Voltage Above Threshold | GO to Pinpoint Test AD |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.