Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2017 Ford Escape SFACTORY OEM SERVICE PROCEDURE
Am/Fm/Cd/Sync/Touchscreen Display: FCIM
| DTC | Description | Action |
|---|---|---|
| B13DC:11 | Compact Disc Slot Illumination: Circuit Short To Ground | REFER to: Instrument Panel and Interior Switches Illumination . |
| B13DC:12 | Compact Disc Slot Illumination: Circuit Short To Battery | REFER to: Instrument Panel and Interior Switches Illumination . |
| B13DC:13 | Compact Disc Slot Illumination: Circuit Open | REFER to: Instrument Panel and Interior Switches Illumination . |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to Pinpoint Test AI |
| U0257:87 | Lost Communication With Front Controls / Display Interface Module: Missing Message | GO to Pinpoint Test AO |
| U0423:00 | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC. Refer to: INFORMATION CENTER - INSTRUMENTATION, MESSAGE CENTER AND WARNING CHIMES
. If no Diagnostic Trouble Codes (DTCs) are present in the IPC, DIAGNOSE the observable symptom. |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U2013:63 is retrieved again, Refer to FCIM HARDWARE TESTING |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to incomplete or incorrect PMI procedures. CHECK vehicle service history for recent service actions related to the FCIM. If there have been recent service actions with this module, INSTALL as-built data from PTS, following the diagnostic scan tool instructions under Module Programming>As-Built. Refer to: Module Configuration - System Operation and Component Description . If there have been no recent service actions, Refer to FCIM HARDWARE TESTING . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, Refer to FCIM HARDWARE TESTING |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, Refer to FCIM HARDWARE TESTING |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AP |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AQ |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.