2017 Ford Escape SFACTORY OEM SERVICE PROCEDURE

Transfer Case

WARNING: This page is about a different variant/trim than selected.

All vehicles 

  1. Install a new compression seal.
    GFD184447Courtesy of FORD MOTOR COMPANY
  2. Install the PTU.
    GFD184445Courtesy of FORD MOTOR COMPANY
  3. Install the new top PTU bolts.

    Torque: 59 lb.ft (80 Nm)

    GFD184448Courtesy of FORD MOTOR COMPANY
  4. Install the new bottom PTU bolts.

    Torque: 59 lb.ft (80 Nm)

    GFD184449Courtesy of FORD MOTOR COMPANY
  5. Check the PTU fluid level. Refer to: Transfer Case Fluid Level Check .

    2.0L EcoBoost (177kW/240PS) - MI4 

  6. Install the PTU support bracket and the support bracket bolts.

    Torque:

    1: 18 lb.ft (25 Nm)

    2: 46 lb.ft (63 Nm)

    GFD184450Courtesy of FORD MOTOR COMPANY

    1.5L EcoBoost (132kW/180PS) - I4/1.6L EcoBoost (132kW/180PS) - Sigma 

  7. NOTE: 2.0L shown. 1.5L and 1.6L similar.

    Install the PTU support bracket and the support bracket bolts.

    Torque :: 18 lb.ft (25 Nm)

    GFD184451Courtesy of FORD MOTOR COMPANY

    All vehicles 

  8. Connect the PTU vent hose.
    GFD184429Courtesy of FORD MOTOR COMPANY
  9. Install the PTU heat shield and heat shield bolts.

    Torque: 97 lb.in (11 Nm)

    GFD184441Courtesy of FORD MOTOR COMPANY
  10. Install the RH halfshaft. Refer to: Front Halfshaft RH .

    2.0L EcoBoost (177kW/240PS) - MI4 

  11. Install the catalytic converter. Refer to: Catalytic Converter .
  12. Install the CAC tube.

    Torque:

    1: 44 lb.in (5 Nm)

    2: 97 lb.in (11 Nm)

    GFD184452Courtesy of FORD MOTOR COMPANY
  13. Install the rear driveshaft. Refer to: Rear Driveshaft .

    1.6L EcoBoost (132kW/180PS) - Sigma 

  14. Install the CAC tube.

    Torque: 44 lb.in (5 Nm)

    GFD184439Courtesy of FORD MOTOR COMPANY

    1.5L EcoBoost (132kW/180PS) - I4/1.6L EcoBoost (132kW/180PS) - Sigma 

  15. Align the index-mark on driveshaft to the PTU pinion flange.
    GFD182919Courtesy of FORD MOTOR COMPANY
  16. Install the new driveshaft-to-pinion flange bolts.

    Torque: 26 lb.ft (35 Nm)

GFD184453Courtesy of FORD MOTOR COMPANY

All vehicles 

GFD184454Courtesy of FORD MOTOR COMPANY
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.