Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2017 Ford C-Max Energi TitaniumFACTORY OEM SERVICE PROCEDURE
Anti-Lock Brake System (Abs) And Stability Control
- Description And Operation
- Anti-Lock Brake System (ABS) And Stability Control - Overview
- Anti-Lock Brake System (ABS) And Stability Control - System Operation And Component Description
- System Operation
- Network Message Chart
- Anti-Lock Brake System (ABS) Function
- Electronic Brake Force Distribution (EBD)
- Supplemental Braking Assist
- Traction Control
- Electronic Stability Control (ESC)
- Roll Stability Control (RSC)
- Hill Start Assist
- Brake Modes
- MyKey ® Interaction
- Stability-Traction Control Indicator (Sliding Car Icon)
- Stability-Traction Control Disabled Indicator (Sliding Car OFF Icon)
- Component Description
- Diagnosis And Testing
- Anti-Lock Brake System (ABS) And Stability Control
- DTC Chart: Anti-Lock Brake System (ABS) Module
- DTC Chart: Steering Angle Sensor Module (SASM)
- DTC Chart: SOBDMC
- Symptom Chart(s)
- Pinpoint Tests
- Pinpoint Test A : C0564:00, U3003:16, U300A:29
- Pinpoint Test B : Wheel Speed Sensor Erratic Signal Faults
- Pinpoint Test C : C0040:64, C0044:28
- Pinpoint Test D : U0140:00
- Pinpoint Test E : The Traction Control System Cannot Be Disabled
- Pinpoint Test F : C0565:00, U3003:17
- Pinpoint Test G : Stability Control Sensor Signal Faults
- Pinpoint Test H : Abs (Anti-Lock Brake System) Pump Motor Control Circuit Faults
- Pinpoint Test I : P193B:86, U0100:00, U0100:87, U1027:00
- Pinpoint Test J : Brake Booster Solenoid Circuit Faults
- Pinpoint Test K : U0126:00
- Pinpoint Test L : U3003:62
- Pinpoint Test M : SASM (Steering Angle Sensor Module) Signal Faults
- Pinpoint Test N : C0021:00, C0021:21, C0021:66, C0021:77
- Pinpoint Test O : Wheel Speed Sensor Electrical Faults - Front
- Pinpoint Test P : Wheel Speed Sensor Electrical Faults - Rear
- Pinpoint Test Q : Brake Booster Diaphragm Travel Sensor Faults
- Pinpoint Test R : Brake Booster Vacuum Sensor Faults
- Pinpoint Test S : Brake Pedal Angle Sensor Faults
- Pinpoint Test T : The Brake Vacuum Pump Runs Continuously Or Never Runs
- Pinpoint Test U : C1029:00, C102B:00
- Pinpoint Test V : U3002:62
- Pinpoint Test W : C006B:00
- Pinpoint Test X : C0021:00, C1015:64, C1015:7A, C1015:7B, P050F:00
- Pinpoint Test Y : C1018:46
- Pinpoint Test Z : C1021:21, C1021:22
- Pinpoint Test Aa : U0293:00, U1026:00
- Anti-Lock Brake System (ABS) And Stability Control
- Removal And Installation
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
