Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2016 Ford Transit Connect TitaniumFACTORY OEM SERVICE PROCEDURE
Vehicles With Am/Fm/Cd/Sync: FCDIM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B11BA:1C | Steering Wheel Audio Switch Pack: Circuit Voltage Out of Range | GO to Pinpoint Test U |
| B11BA:63 | Steering Wheel Audio Switch Pack: Circuit / Component Protection Time-Out | GO to Pinpoint Test U |
| C1001:01 | Vision System Camera: General Electrical Failure | REFER to: Parking Aid . See The Rear Video Is Inoperative. |
| U0155:00 | Lost Communication With Instrument Panel Cluster IPC Control Module: No Sub Type Information | GO to Pinpoint Test Z |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to Pinpoint Test AA |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to Pinpoint Test AB |
| U2013:87 | Switch Pack: Missing Message | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U2013:87 is retrieved again, INSTALL a new FCIM. Refer to: Front Controls Interface Module (FCIM) . |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | This DTC sets due to an incomplete or incorrect FCDIM PMI. CHECK the vehicle service history for recent service actions related to the FCDIM. If there have been recent service actions with the FCDIM, REPEAT/PERFORM the FCDIM PMI procedure as directed by the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . See PMI. If there have been no recent service actions, the FCDIM has failed to retain configuration data. INSTALL a new FCDIM. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to an incomplete or incorrect FCDIM PMI. CHECK the vehicle service history for recent service actions related to the FCDIM. If there have been recent service actions with the FCDIM, REPEAT/PERFORM the FCDIM PMI procedure as directed by the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . See PMI. If there have been no recent service actions, the FCDIM has failed to retain configuration data. INSTALL a new FCDIM. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to an incomplete or incorrect FCDIM PMI. CHECK the vehicle service history for recent service actions related to the FCDIM. If there have been recent service actions with the FCDIM, REPEAT/PERFORM the FCDIM PMI procedure as directed by the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . See PMI. If there have been no recent service actions, the FCDIM has failed to retain configuration data. INSTALL a new FCDIM. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new FCDIM. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the DTC. WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new FCDIM. Refer to: Front Control/Display Interface Module (FCDIM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AD |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AE |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.