Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2016 Ford Transit Connect TitaniumFACTORY OEM SERVICE PROCEDURE
Vehicles With Am/Fm/Cd/Sync/Touchscreen: GPSM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| U0100:00 | Lost Communication with ECM/ PCM "A": No Sub Type Information | GO to Pinpoint Test AC |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to Pinpoint Test AD |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AF |
| U0401:00 | Invalid Data Received from ECM/ PCM A: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the PCM. For vehicles with the 1.6L EcoBoost (132kW/180PS) - Sigma, REFER to: Electronic Engine Controls - 1.6L . For vehicles with the 2.5L Duratec (125kW/170PS), REFER to: Electronic Engine Controls . |
| U0422:00 | Invalid Data Received from Body Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the BCM. Refer to: Body Control Module (BCM) . |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC. Refer to: Instrumentation, Message Center and Warning Chimes . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to an incomplete or incorrect GPSM PMI. CHECK the vehicle service history for recent service actions related to the GPSM. If there have been recent service actions with the GPSM, REPEAT/PERFORM the GPSM PMI procedure as directed by the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . See PMI. If there have been no recent service actions, the GPSM has failed to retain configuration data. INSTALL a new GPSM. |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to an incomplete or incorrect GPSM PMI. CHECK the vehicle service history for recent service actions related to the GPSM. If there have been recent service actions with the GPSM, REPEAT/PERFORM the GPSM PMI procedure as directed by the diagnostic scan tool. Refer to: Module Configuration - System Operation and Component Description . See PMI. If there have been no recent service actions, the GPSM has failed to retain configuration data. INSTALL a new GPSM. |
| U3000:09 | Control Module: Component Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:09 is retrieved again, DISCONNECT the battery for 1 minute, then reconnect it. CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:09 is retrieved again, INSTALL a new GPSM. |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new GPSM. |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new GPSM. |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AO |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AP |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.