Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2016 Ford Edge SportFACTORY OEM SERVICE PROCEDURE
Steering Column Control Module
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1298:09 | Steering Column Adjust Up Switch: Component Failure |
NOTE:
The SCCM continually monitors the steering column control switch input. With battery voltage between 10 and 15.5 volts and with the ignition set to ON, if the SCCM receives switch input for more than 2 minutes, a DTC is set. INSTALL a new steering column control switch. REFER to: Steering Column Control Switch
. CLEAR the SCCM Diagnostic Trouble Codes (DTCs). Using a diagnostic scan tool, CARRY OUT a SCCM self-test. If DTC B1298:09 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM)
. |
| B1299:09 | Steering Column Adjust Down Switch: Component Failure |
NOTE:
The SCCM continually monitors the steering column control switch input. With battery voltage between 10 and 15.5 volts and with the ignition set to ON, if the SCCM receives switch input for more than 2 minutes, a DTC is set. INSTALL a new steering column control switch. REFER to: Steering Column Control Switch
. CLEAR the SCCM Diagnostic Trouble Codes (DTCs). Using a diagnostic scan tool, CARRY OUT a SCCM self-test. If DTC B1299:09 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM)
. |
| B12A1:09 | Steering Column Adjust Out Switch: Component Failure |
NOTE:
The SCCM continually monitors the steering column control switch input. With battery voltage between 10 and 15.5 volts and with the ignition set to ON, if the SCCM receives switch input for more than 2 minutes, a DTC is set. INSTALL a new steering column control switch. REFER to: Steering Column Control Switch
. CLEAR the SCCM Diagnostic Trouble Codes (DTCs). Using a diagnostic scan tool, CARRY OUT a SCCM self-test. If DTC B12A1:09 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM)
. |
| B12A2:09 | Steering Column Adjust In Switch: Component Failure |
NOTE:
The SCCM continually monitors the steering column control switch input. With battery voltage between 10 and 15.5 volts and with the ignition set to ON, if the SCCM receives switch input for more than 2 minutes, a DTC is set. INSTALL a new steering column control switch. REFER to: Steering Column Control Switch
. CLEAR the SCCM Diagnostic Trouble Codes (DTCs). Using a diagnostic scan tool, CARRY OUT a SCCM self-test. If DTC B12A2:09 returns, INSTALL a new SCCM. REFER to: Steering Column Control Module (SCCM)
. |
| All other SCCM Diagnostic Trouble Codes (DTCs) | - | REFER to: Steering Wheel and Column Electrical Components . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
