2015 Ford Transit-350 HD Base, Van Cargo ExtendedFACTORY OEM SERVICE PROCEDURE

Power Steering System Purging

Special Tool(s) / General Equipment 

GFD73560Courtesy of FORD MOTOR COMPANY
211-265 Evacuation Cap, Power Steering TKIT-1999M2-FLM
GFD73562Courtesy of FORD MOTOR COMPANY
416-D002 Vacuum Pump Kit

Materials 

Name Specification
Motorcraft ® MERCON ® LV Automatic Transmission Fluid XT-10-QLVC MERCON ® LVWSS-M2C938-A

Bleeding 

  • 1.

    NOTE: If the air is not purged from the power steering system correctly, premature power steering pump failure may result. The condition may occur on pre-delivery vehicles with evidence of aerated fluid or on vehicles that have had steering component repairs.

    Remove the power steering reservoir cap. Check the fluid.

  • 3.

    Tightly insert the Power Steering Evacuation Cap into the reservoir and connect the Vacuum Pump Kit. Use Special Service Tool: 211-265 Evacuation Cap, Power Steering., 416-D002 Vacuum Pump Kit.
GFD73564Courtesy of FORD MOTOR COMPANY

  • 4.

    Start the engine.

  • 5.

    NOTE: If the Vacuum Pump Kit does not maintain vacuum, check the power steering system for leaks before proceeding. For additional information, refer to Power Steering Fluid Leak Test .

    Using the Vacuum Pump Kit, apply vacuum and maintain the maximum vacuum of 68-85 kPa (20-25 in-Hg). Use Special Service Tool: 416-D002 Vacuum Pump Kit.

  • 6.

    NOTE: Do not hold the steering wheel against the stops for an extended amount of time. Damage to the power steering pump may occur.

    Cycle the steering wheel fully from stop-to-stop 10 times.

  • 7.

    Stop the engine.

  • 8.

    Release the vacuum and remove the Vacuum Pump Kit and the Power Steering Evacuation Cap.

  • 9.

    NOTE: Do not overfill the reservoir.

    Fill the reservoir as needed with the specified fluid.

    Material: Motorcraft ® MERCON ® LV Automatic Transmission Fluid / XT-10-QLVC (MERCON ® LV) (WSS-M2C938-A)

  • 10.

    Start the engine.

  • 11.

    Install the Power Steering Evacuation Cap and the Vacuum Pump Kit. Apply and maintain the maximum vacuum of 68-85 kPa (20-25 in-Hg). Use Special Service Tool: 211-265 Evacuation Cap, Power Steering., 416-D002 Vacuum Pump Kit.
GFD73564Courtesy of FORD MOTOR COMPANY

  • 12.

    NOTE: Do not hold the steering wheel against the stops for an extended amount of time. Damage to the power steering pump may occur.

    Cycle the steering wheel fully from stop-to-stop 10 times.

  • 13.

    Stop the engine, release the vacuum and remove the Vacuum Pump Kit and the Power Steering Evacuation Cap.

  • 14.

    NOTE: Do not overfill the reservoir.

    Fill the reservoir as needed with the specified fluid and install the reservoir cap.

    Material: Motorcraft ® MERCON ® LV Automatic Transmission Fluid / XT-10-QLVC (MERCON ® LV) (WSS-M2C938-A)

  • 15.

    Visually inspect the power steering system for leaks.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.