Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2015 Ford Fiesta STFACTORY OEM SERVICE PROCEDURE
Information System And Entertainment System DTCS (Am/Fm/Cd/Sync/Touchscreen): FCIM
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| U0009:88 (Sony® FCIM only) | High Speed CAN Communication Bus (-) Shorted to Bus (+): Bus off | The module was unable to communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the diagnostic scan tool to report this DTC. VERIFY the integrity of the connectors and wiring. |
| U0155:00 (Sony® FCIM only) | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to Pinpoint Test AE |
| U0155:87 (Non-branded FCIM only) | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to Pinpoint Test AF |
| U0257:00 (Sony® FCIM only) | Lost Communication With Front Controls / Display Interface Module: No Sub Type Information |
NOTE:
Despite the description, this DTC applies to the FDIM, not the FCDIM. GO to Pinpoint Test AK |
| U0257:87 (Non-branded FCIM only) | Lost Communication With Front Controls / Display Interface Module: Missing Message |
NOTE:
Despite the description, this DTC applies to the FDIM, not the FCDIM GO to Pinpoint Test AL |
| U0423:00 (Sony® FCIM only) | Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC. REFER to: Instrumentation, Message Center and Warning Chimes . |
| U2013:63 | Switch Pack: Circuit/Component Protection Time-Out | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U2013:63 is retrieved again, INSTALL a new FCIM. REFER to: Front Controls Interface Module (FCIM) . |
| U201A:51 (Non-branded FCIM only) | Control Module Main Calibration Data: Not Programmed | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect PMI procedures. If there have been recent service actions with this module, REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. REFER to: Module Configuration - System Operation and Component Description . See Programmable Module Installation (PMI). If there have been no recent service actions, INSTALL a new FCIM to correct the failure to retain configuration data. REFER to: Front Controls Interface Module (FCIM) . |
| U3000:41 | Control Module: General Checksum Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:41 is retrieved again, INSTALL a new FCIM. REFER to: Front Controls Interface Module (FCIM) . |
| U3000:42 | Control Module: General Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:42 is retrieved again, INSTALL a new FCIM. REFER to: Front Controls Interface Module (FCIM) . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to Pinpoint Test AM |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to Pinpoint Test AN |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.