2015 Ford Edge Sport, FWDFACTORY OEM SERVICE PROCEDURE

Possible Causes

Network concern 

BCM configuration concern 

ABS Module 

  1. PA1: CHECK THE ABS MODULE AND BCM DTCS 
    • Ignition ON, engine OFF.
    • Carry out the ABS self-test.
    • Carry out the BCM self-test.
    • Are any communication or module internal failure DTCs present? 
      Yes No
      For the ABS module, REFER to the ABS Module DTC Chart.
      For the BCM, REFER to Multifunction Electronic Modules .
      Go to  PA2.
  2. PA2: RECHECK FOR ABS MODULE DTC U0300:00 
    • Clear the ABS DTCs.
    • Ignition OFF.
    • Ignition ON, engine OFF.
    • Carry out the ABS self-test.
    • Is DTC U0300:00 still present? 
      Yes No
      Go to  PA3. The concern was caused by the installation of a new BCM. The repair is complete.
  3. PA3: PROGRAM THE ABS MODULE 
    • Using a diagnostic scan tool, carry out the PMI for the BCM using as-built data.
    • Ignition OFF.
    • Ignition ON, engine OFF.
    • Carry out the ABS self-test.
    • Is DTC U0300:00 still present? 
      Yes No
      Go to  PA4. The concern was caused by a incomplete or improperly programmed BCM, the repair is complete.
  4. PA4: PROGRAM THE BCM 
    • Using a diagnostic scan tool, carry out the PMI for the BCM using as-built data.
    • Ignition OFF.
    • Ignition ON, engine OFF.
    • Carry out the ABS self-test.
    • Is DTC U0300:00 still present? 
      Yes No
      Go to  PA5. The concern was caused by a incomplete or improperly programmed BCM, the repair is complete.
  5. PA5: CHECK FOR CORRECT ABS MODULE OPERATION 
    • Ignition OFF.
      NOTE: The battery must be removed to access the ABS module electrical connector.
    • Remove the battery. Refer to the appropriate procedure in Charging System (Battery, Mounting And Cables) .
    • Disconnect and inspect the ABS module connector (if not previously disconnected).
    • Repair:
      • -corrosion (install new connector or terminal - clean module pins)
      • -damaged or bent pins - install new terminals or pins
      • -pushed-out pins - install new pins as necessary
    • Reconnect the ABS module connector. Make sure it seats and latches correctly.
    • Install the battery. Refer to the appropriate procedure in Charging System (Battery, Mounting And Cables) .
    • Operate the system and determine if the concern is still present.
    • Is the concern still present? 
      Yes No
      CHECK OASIS for any applicable Technical Service Bulletins TSBs.
      If a TSB exists for this concern, DISCONTINUE this test and FOLLOW the TSB instructions.
      If no TSBs address this concern, INSTALL a new ABS module. Refer to Anti-Lock Brake System (ABS) And Stability Control .
      The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. ADDRESS the root cause of any connector or pin issues.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.