2014 Ford Focus Titanium, 4D Hatchback, Automatic DCT Trans, Gas/EthanolFACTORY OEM SERVICE PROCEDURE

Global Positioning System Module (GPSM) - Sony Sound DTC Table

DTC INDEX

DTC Description Action
U0140:00 Lost Communication With Body Control Module: No Sub Type Information GO to PINPOINT TEST AF
U0155:00 Lost Communication With IPC  Control Module: No Sub Type Information GO to PINPOINT TEST AH
U0422:00 Invalid Data Received from Body Control Module: No Sub Type Information RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the BCM  . REFER to: BODY CONTROL MODULE (BCM) .
U0423:00 Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC  . REFER to: INSTRUMENTATION, MESSAGE CENTER AND WARNING CHIMES .
U2100:00 Initial Configuration Not Complete: No Sub Type Information CHECK vehicle service history for recent service actions related to this module. This DTC  sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new GPSM  to correct the failure to retain configuration data. REFER to: GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U2101:00 Control Module Configuration Incompatible: No Sub Type Information CHECK vehicle service history for recent service actions related to this module. This DTC  sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new GPSM  to correct the failure to retain configuration data. REFER to: GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3000:09 Control Module: Component Failure
  • CLEAR the Diagnostic Trouble Codes (DTCs).
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC  U3000:09 is retrieved again, PERFORM a battery reset by disconnecting the battery for 5 minutes, then reconnecting it.
  • CLEAR the Diagnostic Trouble Codes (DTCs).
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC  U3000:09 is retrieved again, INSTALL a new GPSM  .

    REFER to: GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3000:41 Control Module: General Checksum Failure
  • CLEAR the Diagnostic Trouble Codes (DTCs).
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC  U3000:41 is retrieved again, INSTALL a new GPSM  .

    REFER to: GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3000:42 Control Module: General Memory Failure
  • CLEAR the Diagnostic Trouble Codes (DTCs).
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC  U3000:42 is retrieved again, INSTALL a new GPSM  .

    REFER to: GLOBAL POSITIONING SYSTEM MODULE (GPSM) .
U3003:16 Battery Voltage: Circuit Voltage Below Threshold GO to PINPOINT TEST AN
U3003:17 Battery Voltage: Circuit Voltage Above Threshold GO to PINPOINT TEST AO
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.