Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014FOCUS TITANIUM, 4D HATCHBACK, AUTOMATIC DCT TRANS, GAS/ETHANOLREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEX (EXCEPT ELECTRIC)INFORMATION & ENTERTAINMENT SYSTEM - AM/FM/CD/SYNC DTCSFRONT CONTROL/DISPLAY INTERFACE MODULE (FCDIM) - PREMIUM DTC TABLE
2014 Ford Focus Titanium, 4D Hatchback, Automatic DCT Trans, Gas/Ethanol
Front Control/Display Interface Module (FCDIM) - Premium DTC Table
2014 Ford Focus Titanium, 4D Hatchback, Automatic DCT Trans, Gas/EthanolSECTION Front Control/Display Interface Module (FCDIM) - Premium DTC Table
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B10BD:11 (vehicles built on or after July 8, 2013) | Multifunctional Switch: Circuit Short to Ground | GO to PINPOINT TEST W |
| B10BD:13 (vehicles built on or after July 8, 2013) | Multifunctional Switch: Circuit Open | GO to PINPOINT TEST W |
| B10BD:23 (vehicles built on or after July 8, 2013) | Multifuctional Switch: Signal Stuck Low | GO to PINPOINT TEST W |
| B11BA:1C (vehicles built before July 8, 2013) | Steering Wheel Audio Switch Pack: Circuit Voltage Out of Range | GO to PINPOINT TEST U |
| B11BA:63 (vehicles built before July 8, 2013) | Steering Wheel Audio Switch Pack: Circuit/Component Protection Time-Out | GO to PINPOINT TEST U |
| U0155:00 | Lost Communication With IPC Module: No Sub Type Information | GO to PINPOINT TEST AB |
| U0184:00 | Lost Communication With Radio: No Sub Type Information | GO to PINPOINT TEST AC |
| U0253:00 | Lost Communication With Accessory Protocol Interface Module: No Sub Type Information | GO to PINPOINT TEST AD |
| U2013:87 | Switch Pack: Missing Message | GO to PINPOINT TEST X |
| U201A:51 | Control Module Main Calibration Data: Not Programmed | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. REFER to: FRONT CONTROL/DISPLAY INTERFACE MODULE (FCDIM) . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. REFER to: FRONT CONTROL/DISPLAY INTERFACE MODULE (FCDIM) . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CHECK vehicle service history for recent service actions related to this module. This DTC sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT/PERFORM the Programmable Module Installation (PMI) procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PROGRAMMABLE MODULE INSTALLATION (PMI) . If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. REFER to: FRONT CONTROL/DISPLAY INTERFACE MODULE (FCDIM) . |
| U3000:41 | Control Module: General Checksum Failure |
|
| U3000:42 | Control Module: General Memory Failure |
|
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AF |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AG |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.