Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2014 Ford Focus Titanium, 4D Hatchback, Automatic DCT Trans, Gas/EthanolFACTORY OEM SERVICE PROCEDURE
Passenger Door Module (PDM) DTC Table
PDM DTC DESCRIPTION
| DTC | Description | Action |
|---|---|---|
| B1087:83 | LIN Bus "A": Value Of Signal Protection Calculation Incorrect | GO to PINPOINT TEST U |
| B1087:86 | LIN Bus "A": Signal Invalid | GO to PINPOINT TEST U |
| B1087:88 | LIN Bus "A": Bus Off | GO to PINPOINT TEST U |
| B1109:11 | Passenger Door Central Locking Motor: Circuit Short To Ground | GO to PINPOINT TEST I |
| B1109:15 | Passenger Door Central Locking Motor: Circuit Short To Battery Or Open | GO to PINPOINT TEST I |
| B110B:01 | Rear Door Passenger Side Central Locking Motor: General Electrical Failure | GO to PINPOINT TEST I |
| B1288:02 | Rear Lock Motor Common Circuit: General Signal Failure | GO to PINPOINT TEST I |
| B12AB:11 | Front Window Position Sensor Power Supply: Circuit Short To Ground | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12B6:11 | Front Lock Motor Common Circuit: Circuit Short To Ground | GO to PINPOINT TEST I |
| B12C2:11 | Puddle Lamp: Circuit Short To Ground | REFER to: INTERIOR LIGHTING . |
| B12C2:15 | Puddle Lamp: Circuit Short To Battery Or Open | REFER to: INTERIOR LIGHTING . |
| B12C3:11 | Rear Window Position Sensor Power Supply: Circuit Short To Ground | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12C4:11 | Mirror Turn Indicator: Circuit Short To Ground | REFER to: TURN SIGNAL AND HAZARD LAMPS . |
| B12C4:15 | Mirror Turn Indicator: Circuit Short To Battery Or Open | REFER to: TURN SIGNAL AND HAZARD LAMPS . |
| B12C5:02 | Front Window Lifter Motor Up Relay: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12C6:02 | Rear Window Lifter Motor Up Relay: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12C7:02 | Rear Window Lifter Motor Down Relay: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12C8:02 | Front Window Lifter Motor Down Relay: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B1D21:62 | Remote Control Switch: Signal Compare Failure (Without Push Button Start) | GO to PINPOINT TEST M |
| B12D8:11 | Mirror Heater Output: Circuit Short To Ground | REFER to: REAR VIEW MIRRORS . |
| B12D8:15 | Mirror Heater Output: Circuit Short To Battery Or Open | REFER to: REAR VIEW MIRRORS . |
| B12DC:02 | Front Window Motion/Position Sensor: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12DC:54 | Front Window Motion/Position Sensor: Missing Calibration | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12DD:02 | Rear Window Motion/Position Sensor: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12DD:54 | Rear Window Motion/Position Sensor: Missing Calibration | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12DE:01 | Front Window Local Up Switch: General Electrical Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12DF:01 | Front Window Local Down Switch: General Electrical Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12E9:02 | Rear Window Local Up/Down Switch: General Signal Failure | REFER to: GLASS, FRAMES AND MECHANISMS . |
| B12FF:11 | Rear Door Switch Illumination: Circuit Short To Ground | REFER to: INSTRUMENT PANEL AND INTERIOR SWITCHES ILLUMINATION . |
| B12FF:15 | Rear Door Switch Illumination: Circuit Short To Battery Or Open | REFER to: INSTRUMENT PANEL AND INTERIOR SWITCHES ILLUMINATION . |
| B1302:11 | Mirror Motor Common: Circuit Short To Ground | REFER to: REAR VIEW MIRRORS . |
| B1C11:11 | Passenger Left/Right Mirror Motor: Circuit Short To Ground | REFER to: REAR VIEW MIRRORS . |
| B1C12:11 | Passenger Up/Down Mirror Motor: Circuit Short To Ground | REFER to: REAR VIEW MIRRORS . |
| U0010:88 | Medium Speed Can Communication Bus: Bus Off | The module was unable to communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the scan tool to report this DTC ). VERIFY the integrity of the connectors and wiring. |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST V |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information | GO to PINPOINT TEST W |
| U0199:00 | Lost Communication With "Door Control Module A": No Sub Type Information | GO to PINPOINT TEST X |
| U0202:87 | Lost Communication With "Door Control Module D": Missing Message | GO to PINPOINT TEST Z |
| U0300:00 | Internal Control Module Software Incompatibility: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new PDM . REFER to: DOOR MODULE . |
| U0401:00 | Invalid Data Received From ECM/PCM A: No Sub Type Information | RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the PCM . Refer to the appropriate diagnostic information for the procedure. |
| U0402:00 | Invalid Data Received From TCM: No Sub Type Information | RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the TCM . Refer to the appropriate diagnostic information for the procedure. |
| U0422:00 | Invalid Data Received From Body Control Module: No Sub Type Information | RETRIEVE and REPAIR all non-network Diagnostic Trouble Codes (DTCs) in the BCM . REFER to: BODY CONTROL MODULE (BCM) . |
| U2010:11 | Switch Illumination: Circuit Short To Ground | REFER to: INSTRUMENT PANEL AND INTERIOR SWITCHES ILLUMINATION . |
| U2010:15 | Switch Illumination: Circuit Short To Battery Or Open | REFER to: INSTRUMENT PANEL AND INTERIOR SWITCHES ILLUMINATION . |
| U2014:44 | Control Module Hardware: Data Memory Failure | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new PDM . REFER to: DOOR MODULE . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new PDM . REFER to: DOOR MODULE . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | CLEAR the Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If the DTC is retrieved again, INSTALL a new PDM . REFER to: DOOR MODULE . |
| U3003:62 | Battery Voltage: Signal Compare Failure | GO to PINPOINT TEST AA |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.