Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2014FOCUS ELECTRICREPAIR AND DIAGNOSISQUICK LOOKUPSDTC INDEX (ELECTRIC)PARKING AID SYSTEM DTCSIMAGE PROCESSING MODULE - B (IPM-B)
2014 Ford Focus Electric
Image Processing Module - B (IPM-B)
2014 Ford Focus ElectricSECTION Image Processing Module - B (IPM-B)
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B115E:08 | Camera Module: Bus Signal/Message Failure | GO to PINPOINT TEST J |
| B115E:49 | Camera Module: Internal Electronic Failure | CLEAR the DTC
. REPEAT the self-test. If DTC
B115E:49 returns, INSTALL a new video camera. REFER to: PARKING AID CAMERA . |
| B115E:54 | Camera Module: Missing Calibration | DTC B115E:54 sets in the Image Processing Module - B (IPM-B) when the video camera is not calibrated. Turn the ignition ON for 5 minutes to allow the Image Processing Module - B (IPM-B)/camera flash operation to complete. |
| B115E:55 | Camera Module: Not Configured | DTC B115E:55 sets in the Image Processing Module - B (IPM-B) when the video camera is not configured. Turn the ignition ON for 5 minutes to allow the Image Processing Module - B (IPM-B)/camera flash operation to complete. |
| C115E:51 | Camera Module Flashing Active: Not Programmed | DTC B115E:55 sets in the Image Processing Module - B (IPM-B) when the video camera is not programmed. Turn the ignition ON for 5 minutes to allow the Image Processing Module - B (IPM-B)/camera flash operation to complete. |
| U0010:88 | Medium Speed CAN Communication Bus: Bus off | REFER to: COMMUNICATIONS NETWORK . |
| U0140:87 | Lost Communication With Body Control Module: Missing Message | GO to PINPOINT TEST Q |
| U0155:87 | Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message | GO to PINPOINT TEST N |
| U2100:55 | Initial Configuration Not Complete: Not Configured | CHECK the vehicle service history for recent service actions related to this module. This DTC
sets due to incomplete or incorrect Programmable Module Installation (PMI) procedures. If there have been recent service actions with this module, REPEAT the Programmable Module Installation (PMI) procedure as directed by the scan tool. REFER to PROGRAMMABLE MODULE INSTALLATION (PMI)
. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . If there have been no recent service actions, INSTALL a new Image Processing Module - B (IPM-B) to correct the failure to retain configuration data. REFER to: IMAGE PROCESSING MODULE B (IPMB) - 5-DOOR . |
| U3006:16 | Control Module Input Power "A": Circuit Voltage Below Threshold | GO to PINPOINT TEST O |
| U3006:17 | Control Module Input Power "A": Circuit Voltage Above Threshold | GO to PINPOINT TEST P |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.