2014 Ford Fiesta Titanium, 4D HatchbackFACTORY OEM SERVICE PROCEDURE

Information System And Entertainment System DTCS (Am/Fm/Cd/Sync/Touchscreen): FCIM

DTC INDEX

DTC Description Action
U0009:88 (Sony® FCIM  only) High Speed CAN Communication Bus (-) Shorted to Bus (+): Bus off The module was unable to communicate on the network at a point in time. The fault is not currently present (the module had to communicate with the diagnostic scan tool to report this DTC  . VERIFY the integrity of the connectors and wiring.
U0155:00 (Sony® FCIM  only) Lost Communication With Instrument Panel Cluster (IPC) Control Module: No Sub Type Information GO to PINPOINT TEST AE
U0155:87 (Non-branded FCIM  only) Lost Communication With Instrument Panel Cluster (IPC) Control Module: Missing Message GO to PINPOINT TEST AF
U0257:00 (Sony® FCIM  only) Lost Communication With Front Controls/Display Interface Module: No Sub Type Information
NOTE: Despite the description, this DTC  applies to the FDIM  , not the FCDIM  .
GO to PINPOINT TEST AK
U0257:87 (Non-branded FCIM  only) Lost Communication With Front Controls/Display Interface Module: Missing Message
NOTE: Despite the description, this DTC  applies to the FDIM  , not the FCDIM 
GO to PINPOINT TEST AL
U0423:00 (Sony® FCIM  only) Invalid Data Received From Instrument Panel Cluster Control Module: No Sub Type Information RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC  .
REFER to: INSTRUMENTATION, MESSAGE CENTER AND WARNING CHIMES .
U2013:63 Switch Pack: Circuit/Component Protection Time-Out
  • CLEAR the Diagnostic Trouble Codes (DTCs).
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC  U2013:63 is retrieved again, INSTALL a new FCIM  .

    REFER to: FRONT CONTROLS INTERFACE MODULE (FCIM) .
U201A:51 (Non-branded FCIM  only) Control Module Main Calibration Data: Not Programmed
  • This DTC  sets due to incomplete or incorrect PMI  procedures. CHECK the vehicle service history for recent service actions related to the ACM  .
U3000:41 Control Module: General Checksum Failure
  • CLEAR the Diagnostic Trouble Codes (DTCs).
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC  U3000:41 is retrieved again, INSTALL a new FCIM  .

    REFER to: FRONT CONTROLS INTERFACE MODULE (FCIM) .
U3000:42 Control Module: General Memory Failure
  • CLEAR the Diagnostic Trouble Codes (DTCs).
  • WAIT at least 10 seconds.
  • REPEAT the self-test.
  • If DTC  U3000:42 is retrieved again, INSTALL a new FCIM  .

    REFER to: FRONT CONTROLS INTERFACE MODULE (FCIM) .
U3003:16 Battery Voltage: Circuit Voltage Below Threshold GO to PINPOINT TEST AM
U3003:17 Battery Voltage: Circuit Voltage Above Threshold GO to PINPOINT TEST AN
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.