Name: AllOEMManuals
Address: 316 Brandywine Ave, Streetman, TX, 75859, US
Telephone: +14699867883
Price range: $$

DTC INDEX

DTC	Description	Action
B10BD:11	Multifunctional Switch: Circuit Short to Ground	GO to PINPOINT TEST T
B10BD:13	Multifunctional Switch: Circuit Open	GO to PINPOINT TEST T
B10BD:23	Multifunctional Switch: Signal Stuck Low	GO to PINPOINT TEST T
U0001:88	High Speed CAN Communication Bus: Bus Off	NOTE: The module was unable to communicate on the network at a point in time. The fault is not currently present since the module had to communicate with the diagnostic scan tool to report this DTC . To avoid repeat network concerns: INSPECT for damaged or corroded wiring at the FCDIM . Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. CLEAR the DTC . WAIT at least 10 seconds. REPEAT the network test with the diagnostic scan tool.
U0140:00	Lost Communication With Body Control Module: No Sub Type Information	GO to PINPOINT TEST Y
U0155:00	Lost Communication With Instrument Panel Cluster IPC Control Module: No Sub Type Information	GO to PINPOINT TEST Z
U0193:00	Lost Communication With "Digital Audio Control Module A:" No Sub Type Information	GO to PINPOINT TEST AA
U0253:00	Lost Communication With Accessory Protocol Interface Module	GO to PINPOINT TEST AB
U0423:68	Invalid Data Received From Instrument Panel Cluster Control Module: Event Information	RETRIEVE and FOLLOW Diagnostic Trouble Codes (DTCs) present in the IPC . REFER to: INSTRUMENTATION, MESSAGE CENTER AND WARNING CHIMES .
U1A00:00	Private Communication Network: No Sub Type Information	GO to PINPOINT TEST U
U2100:00	Initial Configuration Not Complete: No Sub Type Information	This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the FCDIM . If there have been recent service actions with the FCDIM , REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PMI. If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. REFER to: FRONT CONTROL/DISPLAY INTERFACE MODULE (FCDIM) .
U2101:00	Control Module Configuration Incompatible: No Sub Type Information	This DTC sets due to incomplete or incorrect PMI procedures. CHECK the vehicle service history for recent service actions related to the FCDIM . If there have been recent service actions with the FCDIM , REPEAT/PERFORM the PMI procedure as directed by the diagnostic scan tool. REFER to: MODULE CONFIGURATION - SYSTEM OPERATION AND COMPONENT DESCRIPTION . See PMI. If there have been no recent service actions, INSTALL a new FCDIM to correct the failure to retain configuration data. REFER to: FRONT CONTROL/DISPLAY INTERFACE MODULE (FCDIM) .
U3000:00	Control Module: No Sub Type Information	CLEAR the Diagnostic Trouble Codes (DTCs). WAIT at least 10 seconds. REPEAT the self-test. If DTC U3000:00 is retrieved again, INSTALL a new FCDIM . REFER to: FRONT CONTROL/DISPLAY INTERFACE MODULE (FCDIM) .
U3006:16	Control Module Input Power "A:" Circuit Voltage Below Threshold	GO to PINPOINT TEST AF
U3006:17	Control Module Input Power "A:" Circuit Voltage Above Threshold	GO to PINPOINT TEST AG

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.

• Brakes feel soft, pull hard to one side, or make grinding noises.

• The engine overheats, stalls repeatedly, or misfires under load.

• You are missing required tools, torque specs, or safe lifting equipment.

• You are not confident in the next step or safety outcome.

Safety Warning

Front Control/Display Interface Module (FCDIM)

Use the Manual With the Right Hardware

When to See a Mechanic

Rather have a pro handle this?