Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2014 Ford F-150 Limited, RWDFACTORY OEM SERVICE PROCEDURE
Accessory Protocol Interface Module (APIM)
DTC INDEX
| DTC | Description | Action |
|---|---|---|
| B1252:04 | USBÂ Port: System Internal Failure | GO to PINPOINT TEST R . |
| B1252:11 | USBÂ Port: Circuit Short to Ground | GO to PINPOINT TEST R . |
| B12B8:04 | USB Port #2: System Internal Failure |
NOTE:
This DTC refers to USBÂ
port #2 on the APIMÂ
itself, which is not used.
|
| B12B8:11 | USB Port #2: Circuit Short To Ground |
NOTE:
This DTC refers to USBÂ
port #2 on the APIMÂ
itself, which is not used.
|
| B1D79:01 | Microphone Input: General Electrical Failure | GO to PINPOINT TEST P . |
| B1D79:11 | Microphone Input: Circuit Short To Ground | GO to PINPOINT TEST P . |
| B1D79:12 | Microphone Input: Circuit Short To Battery | GO to PINPOINT TEST P . |
| B1D79:13 | Microphone Input: Circuit Open | GO to PINPOINT TEST P . |
| U0140:00 | Lost Communication With Body Control Module: No Sub Type Information | GO to PINPOINT TEST AC . |
| U0155:00 | Lost Communication With Instrument Panel Cluster (IPCÂ ) Control Module: No Sub Type Information | GO to PINPOINT TEST AE . |
| U0423:00 | Invalid Data Received from Instrument Panel Cluster Control Module: No Sub Type Information | RETRIEVE and FOLLOW DTCs present in the IPCÂ . REFER to INSTRUMENTATION, MESSAGE CENTER, AND WARNING CHIMES . |
| U2100:00 | Initial Configuration Not Complete: No Sub Type Information | This DTC sets due to incomplete or incorrect APIMÂ
programming/provisioning. CHECK vehicle service history for recent service actions related to the APIMÂ
. If there have been recent service actions with the APIMÂ
, REPEAT/PERFORM the APIMÂ
programming as directed by the scan tool. REFER to APIM PROGRAMMING
in the Description and Operation portion. If there have been no recent service actions, the APIM has failed to retain configuration data. PERFORM the APIM Hardware Test. refer to  APIM HARDWARE TESTING . |
| U2101:00 | Control Module Configuration Incompatible: No Sub Type Information | This DTC sets due to incomplete or incorrect APIMÂ
programming/provisioning. CHECK vehicle service history for recent service actions related to the APIMÂ
. If there have been recent service actions with the APIMÂ
, REPEAT/PERFORM the APIMÂ
programming as directed by the scan tool. REFER to APIM PROGRAMMING
in the Description and Operation. If there have been no recent service actions, the APIM has failed to retain configuration data. PERFORM the APIM Hardware Test. refer to  APIM HARDWARE TESTING . |
| U3000:04 | Control Module: System Internal Failure | GO to PINPOINT TEST M . |
| U3000:41 | Control Module: General Checksum Failure |
|
| U3000:42 | Control Module: General Memory Failure CLEAR the DTC. |
|
| U3000:88 | Control Module: Bus Off |
NOTE:
Network communication/message DTCs can result from intermittent concerns such as damaged wiring or low battery voltage occurrences. Additionally, vehicle repair procedures such as module reprogramming often set these DTCs. Replacing a module to resolve a network DTC is unlikely to resolve the concern. The module was unable to communicate on the network at a point in time. The fault is not currently present. To avoid repeat network concerns:
|
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | GO to PINPOINT TEST AN . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | GO to PINPOINT TEST AO . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
