Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2014 Ford C-Max Energi SELFACTORY OEM SERVICE PROCEDURE
Occupant Classification System Module (OCSM)
DTC INDEX
| DTCÂ | Description | Action |
|---|---|---|
| B0061:11 | Passenger Seatbelt Tension Sensor: Circuit Short To Ground | REFER to: PINPOINT TEST - DTC: KK . |
| B0061:12 | Passenger Seatbelt Tension Sensor: Circuit Short To Battery | REFER to: PINPOINT TEST - DTC: KK . |
| B0061:13 | Passenger Seatbelt Tension Sensor: Circuit Open | REFER to: PINPOINT TEST - DTC: KK . |
| B0061:1C | Passenger Seatbelt Tension Sensor: Circuit Voltage Out of Range | REFER to: PINPOINT TEST - DTC: KK . |
| B0061:49 | Passenger Seatbelt Tension Sensor: Internal Electronic Failure | REFER to: PINPOINT TEST - DTC: KK . |
| B00C0:11 | Passenger Seat Occupant Classification Sensor "A": Circuit Short to Ground | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C0:1A | Passenger Seat Occupant Classification Sensor "A": Circuit Resistance Below Threshold | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C0:49 | Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C1:11 | Passenger Seat Occupant Classification Sensor "B": Circuit Short to Ground | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C1:12 | Passenger Seat Occupant Classification Sensor "B": Circuit Short to Battery | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C1:49 | Passenger Seat Occupant Classification Sensor "B": Internal Electronic Failure | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| B00C2:11 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Ground | REFER to: PINPOINT TEST - DTC: LL . |
| B00C2:12 | Passenger Seat Occupant Classification Sensor "C": Circuit Short to Battery | REFER to: PINPOINT TEST - DTC: LL . |
| B1193:00 | Crash Event Storage Full and Locked: No Sub Type Information | CLEAR the OCSMÂ
Diagnostic Trouble Codes (DTCs) and REPEAT the self-test. If DTCÂ
B1193:00 returns, INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . REFER to: INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT . |
| U0100:00 | Lost Communication with ECM/PCM A: No Sub Type Information | REFER to: PINPOINT TEST - DTC: GG . |
| U0151:00 | Lost Communication with Restraints Control Module: No Sub Type Information | REFER to: PINPOINT TEST - DTC: HH . |
| U0401:00 | Invalid Data Received from ECM/PCM A: No Sub Type Information | CARRY OUT the PCM self-test. REFER to the INTRODUCTION - HYBRID or REFER to: ELECTRONIC ENGINE CONTROLS - HYBRID ELECTRIC VEHICLE (HEV) . |
| U3000:46 | Control Module: Calibration/Parameter Memory Failure | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U3000:49 | Control Module: Internal Electronic Failure | INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U3000:54 | Control Module: Missing Calibration | Using a diagnostic scan tool, CARRY OUT the OCSÂ
Reset. FOLLOW all instructions on the diagnostic scan tool. If the OCSÂ
Reset was not successful, VERIFY correct installation of the OCS. VERIFY the pressure sensor hose is correctly routed and CORRECT the installation as necessary. REPEAT the self-test. If DTCÂ
U3000:54 is still present, INSTALL a new OCSÂ
sensor. REFER to: OCCUPANT CLASSIFICATION SYSTEM (OCS) SENSOR . |
| U3003:16 | Battery Voltage: Circuit Voltage Below Threshold | REFER to: PINPOINT TEST - DTC: JJ . |
| U3003:17 | Battery Voltage: Circuit Voltage Above Threshold | REFER to: PINPOINT TEST - DTC: JJ . |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
