Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2014 Ford C-Max Energi SELFACTORY OEM SERVICE PROCEDURE
Module Communications Network DTCS: BCM
| DTC | Description | Action |
|---|---|---|
| U0001:88 | High Speed CAN Communication Bus: Bus Off | A High Speed Controller Area Network (HS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the diagnostic scan tool. CLEAR the DTC . REPEAT the network test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0004:00 | High Speed CAN Communication Bus (+) Low: No Sub Type Information | A High Speed Controller Area Network (HS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0005:00 | High Speed CAN Communication Bus (+) High: No Sub Type Information | A High Speed Controller Area Network (HS-CAN) fault is present but the network may still be functional at a degraded level. One or more modules may not communicate and may not be sending or receiving messages. GO to PINPOINT TEST AD |
| U0007:00 | High Speed CAN Communication Bus (-) Low: No Sub Type Information | A High Speed Controller Area Network (HS-CAN) fault is present but the network may still be functional at a degraded level. One or more modules may not communicate and may not be sending or receiving messages. GO to PINPOINT TEST AD |
| U0008:00 | High Speed CAN Communication Bus (-) High: No Sub Type Information | A High Speed Controller Area Network (HS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0009:00 | High Speed CAN Communication Bus (-) Shorted to Bus (+): No Sub Type Information | A High Speed Controller Area Network (HS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0010:88 | Medium Speed CAN Communication Bus: Bus Off | A Medium Speed Controller Area Network (MS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the diagnostic scan tool. CLEAR the DTC . REPEAT the network test with the diagnostic scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0013:00 | Medium Speed CAN Communication Bus (+) Low: No Sub Type Information | A Medium Speed Controller Area Network (MS-CAN) fault is either currently present or was present at a point in time. The BCM can report this DTC while a fault is present because the BCM communicates with the scan tool on the High Speed Controller Area Network (HS-CAN). If no Medium Speed Controller Area Network (MS-CAN) modules communicate, GO to PINPOINT TEST AF If all Medium Speed Controller Area Network (MS-CAN) modules currently communicate, CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0014:00 | Medium Speed CAN Communication Bus (+) High: No Sub Type Information | A Medium Speed Controller Area Network (MS-CAN) fault is present but the network may still be functional at a degraded level. One or more modules may not communicate and may not be sending or receiving messages. GO to PINPOINT TEST AF |
| U0016:00 | Medium Speed CAN Communication Bus (-) Low: No Sub Type Information | A Medium Speed Controller Area Network (MS-CAN) fault is present but the network may still be functional at a degraded level. One or more modules may not communicate and may not be sending or receiving messages. GO to PINPOINT TEST AF |
| U0017:00 | Medium Speed CAN Communication Bus(-) High: No Sub Type Information | A Medium Speed Controller Area Network (MS-CAN) fault is either currently present or was present at a point in time. The BCM can report this DTC while a fault is present because the BCM communicates with the scan tool on the High Speed Controller Area Network (HS-CAN). If no Medium Speed Controller Area Network (MS-CAN) modules communicate, GO to PINPOINT TEST AF If all Medium Speed Controller Area Network (MS-CAN) modules currently communicate, CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
| U0018:00 | Medium Speed CAN Communication Bus (-) Shorted to Bus (+): No Sub Type Information | A Medium Speed Controller Area Network (MS-CAN) fault was present at a point in time. The fault is not currently present since the module is communicating with the scan tool. CLEAR the DTC . REPEAT the network test with the scan tool. VERIFY the integrity of the connectors and wiring. Refer to MODULE COMMUNICATIONS NETWORK for schematic and connector information. |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
